PDF User Manual

INSTURCTION MANUAL 

 

MODEL: 6 Series 

STAND-ALONE 

ACCESS CONTROL UNIT

 

 

Mode:X6                  Model:T6                          Model:06 

 

○

1   “#” Button                       

○

2   “   “ Bell Button 

The Model 6 Series can support 99 employees with 
Proximity Cards or PIN Codes, and it has a back tamper 
switch to detect unauthorized attempts at entry. 
Dimension: 
Model X6:95x58x20mm    
Model T6:110x110x20mm    
Model 06:120x110x18mm 
 

Technical Specifications 

Number    Description 

Specification 

1 

Rated Operating Voltage 

DC12V 

2 

Allowed Operating Voltage Range  DC10V-16VDC 

3 

Static Operating Current 

90mA 

4 

Max Operating Current 

150mA 

5 Operating 

Temperature 

-20˚ C -55˚C 

6 Operating 

Humidity 

0-95% 

 

LED Display 

Mode LED 

DOOR LED 

Occurrence 

Green Red  Green  Red 

Normal condition 

Light 

 

 

 

Secure condition 

 

Light 

 

 

Enter program ode   

 

Light 

 

Release the Lock 

 

 

Light 

 

Tamper  

 

 

Light 

Sound Display 

Occurrence 

  Sound display 

Sound Description 

Valid Press 

One short deep 

deep 

Valid change code  Three short deeps  deep deep deep 

Valid Reader 

One short deep 

deep 

Invalid Code 

One long deep 

deep… 

Invalid Program 

One long deep 

deep… 

 
 

Setting Instroductions 

1.programming Glossary 

Menu  
Number 

Menu Description 

Original 
Settings 

1 

Chang Employee Code1 

2580 

2 

Chang Employee Code2 

0000* 

3 

Chang Program Code 

1234 

4 

Chang Secure Code 

3838 

6 

Set NO/NC and Release Time                      10secs 

7 

Add a Proximity Card or a PIN Code 

 

8 

Delete a Proximity Card or a PIN Code   

Notice: Input 0000- disable the function to the items you 

set above.You must be under normal mode when 
changing the functions. All the changed code can’t 
be same with the system code. 

 
2. How to enter programming Mode 

“#+ Program code ” means in Normal mode, press the 
  key ‘#’ for two seconds until the door LED turns red, then   
input Program code to enter the programming state. 

 

3. Function    Settings 

z

 

  Change User Password 1 

‘#’ + Program code + key 1+ x x x x (new 4-digits code)   
 

z

 

  Change User Password 2 

  ‘#’ + Program code + key 2+ x x x x (new 4-digits code)   

 

z

 

 Change Programming Code 

  ‘#’ + Program code + key 3+ x x x x (new 4-digits code)   

 

z

 

  Change Secure Code 

  ‘#’ + Program code + key 4+ x x x x (new 4-digits code) 

 

z

 

  Set No/NC and Door Release Time 

  (NO= Normal Open NC

：

Normal Close) 

  ‘#’ + Program code + key 6+ x x x x 
    The first two digits ndicates NO(10)/NC(00) 
    The last two digits indicates door release time (second)           

i.e. 12 indicates 12secs 
 

z

 

  Add a new proximity card or a PIN code   

‘#’ +  Program code + key 7+ x x x + show the card to 
card reading area. 
          x x x= card number from 01 to 99 
                                    Or   
‘#’ +    Program code + key 7 + x x x x (4-digits PIN code) 
Notice: If you want to add more cards, please repeat the 
later 2 steps, remember that card number should not be 
repeated or the repeated card will be invalid. 

http://www.mjicka.com                             ShenZhen Angetong Technology Co,.Ltd.                         TEL:+86-0755-83775562

 

 

z

 

  Delete a proximity card or a PIN code 

‘#’ +    Program code + key 8+ x x x + Program Code 
    x x x= the card number you want to cancel 
                       Or   
‘#’ +    Program code + key 8 + x x x x (4-digits PIN code 
you want to cancel) + Program Code 
 

z

 

  Return To Factory Settings 

‘#’ +    Program code + key 0 + Program Code 
 
 

Operations

：

 

How to open door in Normal Mode 

›    Input Open code 1 to open the door 
›    Show a valid proximity card to the card reading to 
open the door 
How to open door in Secure mode 

→

 

  When the Open code 2 is original code (0000),the 

card holders with card numbers 01-10 can use their 
cards to open the door. 

→

    When the Open code 2 is changed to a new code, 

and then show their cards to open the door. 
    Notice: In Secure mode, the card holders with card 
number after 10 can not open the door. 
 

 
Replace a lost Program code or Secure code 

›    Remove power from the controller 
›    Press the REX button 
›    Supply power to the unit with REX button pressed 
›    Release the REX button 
›    —If the controller is in Normal Mode. You have 15 
seconds to set a new Program code into the unit the 
original code 1234, before the controller returns to the 
exiting code. 
    -- If the controller is in Secure mode, you have 15 
seconds to return to the Normal mode bu inputting 3838 
+ #. Then you can set your new Secure code by 
Inputting # +Program code + key 4 +x x x x (new 
Program code) 
 

 
Wiring  

 

Controller without Bell 

Lock strike: connect different locks to different terminals 

--Fail safe Lock strike link to NC 
-- Fail Secure Lock strike link to NO 

 

 

Controller with Bell 

Lock strike--Fail safe Lock strike : “-” + NO 
                        -- Fail Secure Lock strike : “-” + NC 
You can set Lock strike type through controller or wiring. 
Common Requirements

：

 

Power Supply: 
Output Voltage 12V, with bell control 
Door Bell: If the power supply can not support the bell, 
you could install a bell without power. 
 

 

http://www.mjicka.com                             ShenZhen Angetong Technology Co,.Ltd.                        TEL:+86-0755-83775562

For more application information please visit our website http://www.mjicka.com