HATO 400Y User Manual - User Manual

Download PDF User Manual

Full Text Searchable PDF User Manual

HATO 400Y HEL 11C

SLIDING GATE OPERATOR

USER’S MANUAL

OUTLINE

1. Important safety information

………………………

2. Main technical parameters

………………………

3. Installation

…………………………………………

4. Connecting

…………………………………………

5. Control

……………………………………………

6. Check

……………………………………………

7. Maintenance

………………………………………

8.Troubleshooting

…………………………………

1.Important safety information

Carefully read and follow all safety precaution and warnings before attempting to install and use this operator, incorrect

installation can lead to severe injury.



The gate operator should be installed by a qualified technician; otherwise, serious personal injury or property

damage may occur.



The auto-reverse function must be checked during installation to ensure that the gate can auto-reverse in the

event of obstruction.



This auto-reverse function should be regularly inspected and adjusted, if necessary.



When opening or closing the gate, do not attempt to walk or drive through the gate.



Children should not be allowed to play near or operate automatic gates.



The automatic gate operator must be grounded.



Install the gate operator on the inside of the property, DO NOT install it on the outside of the property where the

public has access to it.



Be careful when in close proximity to moving parts where hands or fingers could be pinched.



Do not allow control devices to be placed so that a person can access them by reaching through the gate.



In the event of power failure, an emergency release key allows you to operate the gate manually.



The operator should be switched off before repairing it or opening its cover.



Please erase and reprogram the code after installing the operator.

2. Main technical parameters

3. Installation

The HATO 400 Y rack-driven gate operator operates by forcing a drive rack past a drive gear. The entire configuration

is shown in Fig.1. The gate operator must be installed on the inside of the gate.

Gate preparation

Be sure the gate is properly installed and slides smoothly before installing the DKC400Y sliding gate operator. The

gate must be plumb, level, and move freely.

Conduit

In order to protect the wires, use PVC conduit for wires, conduit must be set into the concrete when it is poured. Wires

within the conduit shall be located or protected so that no damage can result from contact with any rough or sharp

part.

Type

HATO 400Y

Power supply

AC 220V, 50Hz

Motor speed

1400 r/min

Gate moving speed

11m/min (19 teeth)

Output torque

14N

Limit switch

Spring limit switch

Noise

≤

62dB;

Environmental temperature

-20

C~+50

Fig.1

Concrete pad

The base unit of the gate operator requires a concrete pad in order to maintain proper stability. The concrete pad

should be approximately 300mm x 200mm x 200mm deep in order to provide for adequate operation.

Anchors

You can use the anchors, bolts, washers and nuts that are provided with the operator. These anchors must be set into

the concrete when it is poured, or you can use wedge anchors.

Operator

In locations where ground freeze is possible, mount the gate operator on installation pad as shown in Fig.2. Check the

operator and make sure it is lined up with the gate.

Conduit

Installation pad

Gate operator

Gear

Nut

Spring washer

Plain washer

Anchor

Bolt

Nut

Spring limit switch

Wires

Fig.2

Installation of rack (see Fig.3)

﹡

If you have installed an external

button switch, you must use two

conduits: one for main power wire,

another one for low voltage wire

(button switch).



Fix the three nuts (in the same package with rack) on the rack element.



Lay the first piece of rack on the gear and weld the first nut on the gate.



Move the gate manually, checking if the rack is resting on the gear, and weld the second and third nut.



Bring another rack element near to the previous one. Move the gate manually and weld the three nuts as the first

rack, thus proceeding until the gate is fully covered.



When the rack has been installed, to ensure it meshes correctly with the gear.



The space between rack and gear is about 1mm.

Fig.3

Spring limit switch



To ensure safety, it is recommended to install plastic blocks at both ends of the gate to prevent the gate from

sliding out of the rail. The rail must be installed horizontally.



Install the plastic block as shown in Fig.4 and Fig.5. The spring limit switch and blocks are used to control the

position of the gate.



Release the gear clutch with the key and push the sliding gate manually to pre-determine the position, fix the

block to the rack and then tighten the gear clutch with the key. Moving the gate electrically, adjust the block to the

proper position until the position of the opening and closing meet the requirement.

Block

Gate

Rack

Gear

Guide rail

Spring limit switch

Nut

Fig.4

Rack

Left block

Right block

Fig.5

CONFORMITY DECLARATION:

Motor Hato 400Y meets the requirements set out in the following provisions:

’

s in accordance with Machine Directive 2006/42/WE and following modify.

’

s in accordance with the following directive CE:

Electromagnetic compatibility Directive EMC 2014/30/UE and following modify.
Low tension Directive LDV 2014/35/UE and following modify.
Have been applied the following harmonized norms:
EN60335-1:2012, EN60335-2-103:2015-3, EN 55014-1:2012, EN 55014-2:2015-06,
EN 61000-3-2-2014-10, EN 61000-3-3:2013-10

Controller of Gate

Drives for 230Vac

500W Motors

USER’S MANUAL

SOFTWARE

MARKING

NOTES

1.2.0-C-NO

11:8.2.2/6.1.0

HEL11C

Before the installation and first use of the controller read the manual carefully and keep it for future reference.

According to the Machinery Directive 2006/42/CE, the product must not be put into service until the final
machinery into which it is to be incorporated or of which it is to be a subassembly has been declared in
conformity with the provisions of directives and relevant regulations which the final machinery must
comply with.

Safety recommendations and precautions:

Before installing and using the drive read all safety warnings and rules. Incorrect installation and failure to
observe the standards included in the manual can cause serious accidents.

•

The controller can be installed only by qualified personnel with relevant licences.

•

A basic protection against electrostatic discharges (ESD) shall be provided during the installation.

•

Caution shall be exercised during the installation. The controller uses the 230Vac voltage (hazardous to

health and life).

•

All works related to the correct functioning of the device (connection, start-up, operation) must be performed

in accordance with relevant regulations concerning the use of electrical machines and in line with the OHS
regulations.

•

Do not connect the supply voltage earlier than specified in this manual! Failure to comply with this

recommendation can cause an electric shock.

•

Check the gate condition before starting the installation: the gate should not swing too much, it should move

easily and smoothly.

•

Before the installation, remove unnecessary ropes and secure the equipment, e.g. locks.

•

Children, disabled persons and mechanical vehicles should not be present in the vicinity of the gate during

the installation.

•

All fixed controls should be located near the gate, but away from the moving parts and out of reach of

outsiders.

•

Disconnect the power supply before repairing or removing any part of the gate.

•

Children and mentally disabled persons must not operate the gate by themselves.

•

Motor and applicable force can be done by qualified personnel equipped with gauge force meter.

•

In the controller without encoder input it is necessary to connect gate optical curtain or other safety elements

preventing from accidentally crush.

•

Fluorescent lamps cannot be connected to the controller.

The controller can be used only in specified applications.

Failure to observe these instructions can lead to serious injuries or destruction of the equipment. The
manufacturer will not be liable for losses and disruption in work resulting from non-observance of this installation
and operation manual.

According to relevant regulations concerning the disposal of used equipment by the private

users in the European Union, an object bearing this symbol

MUST NOT

be disposed of

together with regular wastes. In such case the user is responsible for correct disposal by
delivering the equipment to a specialized outlet or to the manufacturer who will take care of

the further disposal. Separate collection and recycling of used equipment facilitates the
environmental protection and ensures that disposal is carried out in a manner safe to human
life and the environment. This remark also applies to spent batteries, disposable and
rechargeable.

Version :

HEL11C

•

–

cooperates with

Hato’s transmitters operating at a 433.92 MHz frequency and compatible with

Keeloq protocol.

•

– with encoder input

•

– lamp control by relay

Table of contents:

OUTLINE

........................................................................................................................................................................................... 2

Anchors

............................................................................................................................................................................................. 4

1. Application and functionality of HEL11C

. ......................................................................................................................... 10

2. Installation

.................................................................................................................................................................................. 10

2.1 Limit switches connection .................................................................................................................................... 10

2.3 Photocell connection ........................................................................................................................................... 10

2.4 Step-By-Step pushbutton connection .................................................................................................................. 11

2.5 Capacitor connection ........................................................................................................................................... 11

2.6 Motor connection ................................................................................................................................................ 11

2.7 Signalling lamp connection .................................................................................................................................. 11

2.8 Mains supply connection ..................................................................................................................................... 11

2.9 Open direction check ........................................................................................................................................... 11

2.10.1 Motor power adjustment (HEL11C version) ................................................................................................... 11

2.10.2 Applicable force adjustment -(HEL11C) ........................................................................................................ 11

2.11 Optional STOP button connection ..................................................................................................................... 11

Settings and programming

.................................................................................................................................................... 11

3.1 Autoclose.............................................................................................................................................................. 11

3.2 Autoclose time setting ......................................................................................................................................... 12

3.3 Open only function ............................................................................................................................................... 12

3.4 Automatic wicket ................................................................................................................................................. 12

3.5 Signalling lamp ..................................................................................................................................................... 12

Transmitters deleting and programming

........................................................................................................................... 12

4.1 Deleting all transmitters....................................................................................................................................... 12

4.2 Transmitters programming .................................................................................................................................. 12

4.3 Remote transmitter programming (not available in HEL11H) ............................................................................. 12

5. Technical specification:

.......................................................................................................................................................... 14

6. Dimension

.................................................................................................................................................................................. 14

7. Controller wiring diagram

...................................................................................................................................................... 16

1. Application and functionality

of HEL11C

The controller is designed for gate drives with 230Vac

motors.  A  perfect  choice  for  continuous  operation,  the
controller  can  be  used  in  community  car  parks,  private
homes  and  corporate  compounds.    Applied  Microchip

rolling code technology prevents from not authorized
entrance.

The controller cooperates with monostable

pushbutton with Step-By-Step functionality,
(OPEN-STOP-CLOSE-STOP) The control unit perform

following operations: Autoclose, Open only and Automatic
wicket The are two available main versions. First one
with encoder input, and second one without it.

2. Installation

Install the controller into drive. All dimensions are in the
Picture 1. After correct installation continue with
electrical connection.

The manufacturer will not be liable for losses and

disruption in work resulting from non-observance of this
installation, operation manual and applicable regulations.

2.1 Limit switches connection

At first connect limit switches to the controller inputs
marked as (

16,17,18

). Check the gate condition: the gate

should not swing too much, it should move easily and
smoothly between limit positions. If necessary adjust
placements of magnetic parts.

16 (OL)

—

open limit,

17 (CL)

—

close limit,

18 (COM)

—

common, (white wire)

The controller cooperates with Normally Open or Normally
Closed limit switches. To change type of limit switches
solder the ZS jumper on PCB. With soldered jumper

version marked as NO cooperates with NC type switches
and version marked as NC cooperates with NO switches.

If you have cotroller without encoder input - skip point 2.2.

2.2 Encoder connection

Motor encoder must be connected to the inputs marked as
"ENCODER" (Pic.2)(

21,22,23,24

Connect the encoder wires to the plug according to wiring
diagram description. The controller uses encoder impulses
to calculate applicable force. Uncorrect connection may

cause unproper operation and hazardous situation to healt
and life.

─ ─

- encoder signal

- + + + - GND

─x─

- GND

- supply (+5V)

Enkoder parameters: 717 impulses per second (speed
1450rpm)

2.3 Photocell connection

Photocell barrier is a necessary safety element which

must be connected to the controller. It increases safety
and prevents a gate wing from hitting a car, a person or an
object

which are within the photocells’

range. In the

controller without encoder input it is necessary to connect
gate optical    curtain or other safety elements preventing
from  accidentally  crush.  It  should  be  in  series  with
photocell.

–

Photocell supply +24Vdc

–

Photocell supply GND

13-14

–

Normally Closed contact

Output (+24V) current cannot exceed < 450mA. Make
sure power consumption of all connected accesorries.

Example of photocell connection is shown on the wiring
diagram.

The controller uses the 230Vac voltage and
it can be installed only by qualified
personnel with relevant licences

Mains supply must be protected by earth
leakage circuit breaker

2.4 Step-By-Step pushbutton connection

Connect the SBS pushbutton using 2x 0,5mm

wire which

parameters are according to regulations: CEI 20-22; CEI

EN50267-2-1.  Maximum  distance of  connection  depends
on  selected  wire.  Series  resistance  should  not  exceed
100ohms.

Connect momentary pushbutton switch to the inputs
marked as S1 (

) and COM (

2.5 Capacitor connection

Connect capacitor to the inputs on the left side marked as

2.6 Motor connection

Connect motor’s wires to the left connector plug according

to description or wiring diagram:

11 (COM)

–

common

10 (OPEN)

–

open direction

7 (CLOSE)

–

close direction

1 (PE)

–

protective earth PE (yellow-green wire)

2.7 Signalling lamp connection

Connect signalling lamp (230Vac) to the inputs on the left
side marked as

5 (neutral

–

blue wire)

and

6 (phase

–

brown wire).

Lamp power cannot exceed 15W/230V.

When used lamp with built-in flashing module before
installation switch off the flashing function in the controller
(according to 3.5 point).

2.8 Mains supply connection

Mains connection should be applied at the end of

installation. Connect mains wires to the inputs on the left
side marked as:
2 (PE)

–

protective ground (yellow-green wire)

3(L)

–

phase wire (brown wire)

4 (N)

–

neutral wire (blue wire)

Before first using check the correct power supply,

ground protection and wire connections. Wires
should be as short as possible. Keep control wires
away from high current wires. Avoid wires loop.

2.9 Open direction check

Set the gate manually in the middle position. The first

command after powering up is “open”

. Press the SBS or

programmed transmitter button. If drive works in closing

direction stop the motor, switch off the power supply and

switch motor’s leads connected to the inputs

OPEN(

)

and CLOSE(

If the drive operates properly check functionality of all
connected accessories. In case of problems check wiring
connection and adjust motor force or applicable force

setting.

2.10.1

Motor

power

adjustment

(HEL11C

version) ??

Fitted on the control unit “P” potentiometer adjusts

maximum  motor  power.  Take  great  care  when  adjusting
the  power  as  this  may  affect  the  level  of  safety  of  the
automatic  system.

Measure the force applied to the

gate and compare it with regulatory values.

2.10.2 Applicable force adjustment -(HEL11C)

The  controller  uses  encoder  impulses  to  calculate
applicable  force.  To  adjust  the  sensivity  of  the  controller
use  the

“P” potentiome

ter. In minus direction sensitivity

decreases, in plus direction sensitivity increases.

Adjustment must be carried out according to
applicable regulations.

2.11 Optional STOP button connection

Connect external normally closed switch according to
wiring diagram.

Settings and programming

3.1 Autoclose

In the autoclose operation mode, an opening manoeuvre

is  followed  by  a  pause  and  then  an  automatic  closing
manoeuvre. The closing time is determined by the delay in
turning  off  the  light.  It  is  activated  when  the  OPT1
(DIPSWITCH)  micro-switch  is  put  to  ON.  When  the

Auto-close function is active, the principle of light
operation is different: the light is slowly flashing when the
gate is opening, the light is on when the gate stays open,

and is flashing during automatic closing. When the
gate stops, the light is off. The Auto-close function

Disconnect the power supply before checking
wire connection.

The controller uses the 230Vac voltage and

it can be installed only by qualified
personnel with relevant licences

necessitates photocells to ensure user safety (to prevent
gate from closing when an obstacle is within its range!). in

addition, the photocells will reduce the opening time. The
controller will detect the passage of a vehicle and will
close the gate after 5 seconds. When the Auto-close

function is active, all programming procedures can be
performed only when the gate is stopped after closing.

3.2 Autoclose time setting

To program the controller use the LEARN button and the
LED on the controller board. Press the LEARN button less

than 3s, the LED will light up. Then, by pressing the same
button you can set the delay time. One keystroke
corresponds to 15 seconds, (e.g. 4 keystrokes mean 1

minute; the LED dims at each keystroke). When you have
finished programming, the processor will automatically
save the settings after 3s, flash the LED three times and

return to normal operation.

Example of autoclose time setting shows Tab1.1

3.3 Open only function

Open-only function facilitates communication

through entry-exit and guarantees that a third party will not
close or stop the gate in the least opportune moment.
Photocells are necessary for safety. It works only with the

Auto-close function and is activated by putting the  OPT1
and  OPT2  micro-switches  to  ON.  A  command  from  the
remote  or  from  manual  control  will  tell  the  controller  to

open the gate in each case, and then the gate will be
closed by the Auto-close function.

3.4 Automatic wicket

It is activated when the OPT3 (DIPSWITCH) micro-switch
is put to ON. In the automatic wicket operation mode,

when the controller will detect the passage of a vehicle or
person (photocell) during opening the gate will stop. To
c

lose the gate push the SBS or programmed transmitter’s

button.  When  autoclose  function  is  also  activated  when
the  controller  will  detect  passage  the  gate  will  stop  and
after 5s will close.

3.5 Signalling lamp

It can work in two modes. In the first mode, as warning

signals when the gate is moving. In the second one, as an
auxiliary lighting of a vehicle or garage with delayed off. In
the second mode the lamp is on when gate is moving.

To switch off second mode put the OPT1 (DIPSWITCH)
micro-switch to OFF. Press the LEARN button less than 3s,
the LED will light up. Wait 3s, the controller will flash the

LED tree times and return to normal operation.

Transmitters deleting and

programming

4.1 Deleting all transmitters

Press the LEARN button and hold, the LED will light up,
go out and then it will start to flash. Release the button.
The deleting procedure is completed. We recommend that

this procedure is performed right after installation.

4.2 Transmitters programming

You can program up to 40 remot

e controls with Keeloq’s

rolling code. Each remote must be programmed

separately. Press LEARN and hold until the LED lights up
and goes out. Release the button. Now you have 10
seconds to press a selected button in the remote control.
When the LED flashes three times, the learning process

has been completed successfully. If you wish to program
more transmitters, after three LED flashes you have next
10 seconds to program the second remote, etc. A single

LED flash means that the learning process is finished.
When you have programmed 40 remotes, the memory is
full and the LED will flash only two times and will return to

the normal operation. If the memory is full, check if you
really use 40 remotes. If you use fewer than 40 remotes,
clear the memory and reprogram all remotes, and when
you use more than 40 remotes use an additional module

eL3 which will increase the number of transmitters to 64.
When the learning error occurs, repeat the programming
and if this does not help either use another remote in good

working order. If you still fail, contact the authorized
service.

4.3 Remote transmitter programming

It is possible to program new transmitter using

four-channel earlier programmed transmitter. The gate

must  be  fully  open.  Push  the  C  and  D  buttons  of  the
programmed  transmitter  for  5s.  The  signalling  lamp  will
light  up.  Now  you  have  5  seconds  to  press  a  selected

button in the new remote controller. When the lamp
flashes three times, the learning process has been
completed successfully. A single LED flash means that the

learning process is finished.

Tab.1.1. Autoclose time setting

(e.g.)

1. Press the LEARN button.

The LED will light up. Release the button.

2. Then, by pressing the same button you can set the delay time. One keystroke

corresponds to 15 seconds, (e.g. 4 keystrokes mean 1 minute; the LED dims at

each keystroke).

3. Wait 3s, the controller flash the LED three times and return to normal operation.

3s
3x

Tab.1.2 Deleting all transmitters

Press the LEARN button and hold, the LED will light up, go out and then it will start

to flash. We recommend that this procedure is performed right after installation.

2. Release the button. The deleting procedure is completed.

Tab.1.3 Tranmistters programming

1. Press LEARN and hold until the LED lights up and goes out. Release the button.

2. Now you have 10 seconds to press a selected button in the remote control. When
the LED flashes three times, the learning process has been completed successfully.

10s

3. When the LED flashes three times, the learning process has been completed
successfully. A single LED flash means that the learning process is finished.

    3x                  10s

LEAR
N

SW1

5. Technical specification:

Power supply:

AC 230V, 50Hz

Curren consumption in standby:

< 25mA AC

Powe consumption in standby:

< 10 W

Transmitters range:

<200m

Frequency:

433,92MHz

Transmitters type:

Version

HATO Keeloq

Transmitters memory:

40 pcs

Autoclose max time:

5s - 10min

Operation max time:

120 sec.

Operating temperature:

20ºC +70ºC

Fuse type:

5A/230V, ø5x20

6. Dimension

HATO 400Y SLIDING GATE OPERATOR USER

’S MANUAL

7. Controller wiring diagram

Picture 2

HATO 400Y SLIDING GATE OPERATOR USER

’S MANUAL

DISTRIBUTOR/SALESMAN

Hato Polska S.C

Tomas

z Słodkowski –

Harmeet Singh

ul. Tunelowa 57

40-676 Katowice

POLAND

Warehouse/sales/service

ul. Żeromskiego 1

41-205 Sosnowiec

tel. 032/ 785-25-42