Related Product Video
Full Text Searchable PDF User Manual
Great effect variety
Delicate and streamline appearance to allow movement and
installation be easier
Smooth 570 rotation angle about the x-axis and 270 rotation angle
about the Y-axis, electronic sensor to automatically reset
CMY mixer to allow the color to be various and richer and make color
adjustment more accurate by adding offset color micro-adjusting
One color disk with six dichroic color and open, which contains 3200°
K CTC, be able to rotate in both directions smoothly to create heart-
touching rainbow effect, in order to make color adjustment more
convenient, a color macro function is added and in order to make
color adjustment more accurate, an offset color micro-adjusting
function is added
10-30 degree ZOOM effect
Frost lens with soft-edge frost
1-12fps fast flash with random and 0-100% mechanical exposure
Sophisticated appearance and structure design
Stylish, high impact resistant polymer shell, which is lighter than
anyone else of the same class in the market.
Solid square base is convenient set on the TRUSS, or directly stand
on the ground or stage for uses.
Systematic modular construction design has all inner function wheels
and PCBs modularized, which allows version update or customization
Sophisticated optical system makes light output more bright and
Simple and easy operation
Standard USITT DMX512 protocol, 15 or 13 DMX Channel.
High-torque stepper motors, smooth and precise micro-stepping
LED screen controls DMX coding and built-in functions' election, as
well as also display lamp's time usage.
Description of the appearance
Carefully unpack the carton, and make sure if any damage or loss
caused by transportation.
Contact your Geni dealer to assure your right by telephone or
facsimile immediately if damage has occurred or if something is
A. OBY-600 Wash
This appliance must be earthed (grounded).
Disconnect power before removing covers or servicing.
Keep case closed while operating.
OBY-600 contains no user serviceable parts. Refer servicing to
qualified technicians only.
Lamp and components become hot during operation. Allow time to
cool before handling.
Keep flammable material at least one meter away from unit.
Do not operate in wet conditions or near liquids.
Keep air vents clear to avoid overheating.
Lamp produces hazardous UV light. Do not look directly at lamp
Replace any blown or damaged fuses only with those of identical
Remove the power cord before installing the lamp.
Keep projector-head upward (See Figure below.) and loosen four
screws on the cover with appropriate tool then open the top cover
and put it aside.
Loosen and grab the screws
on the shutter cover with
Wear the gloves and extract the lamp from
the package, loosen the screws on both sides of
the lamp, then slide the lamp paralleled into the
lamp socket. Adjust the round point of the
lamp upward (See Figure.) and fasten the
Reverse the above-mentioned processes for
the complete installation.
Pull the reflector backward
Oby-600 can be set on the flat stage floor directly or use clamp to mount on
any kinds of trusses for fitting the mobility of various venues.
Mount two attached brackets(a) on the bottom (See Figure ), and
collocate the appropriate clamps(b) to rig with trusses. Must use the
safety ropes that can hold the ten times as heavy as the fixture through
the eye bolts(c) on the bottom of the base and trusses; then join the
safety ropes with screw-on carabines(d).
Use 3-pin XLR data cables to link the controller to DMX lighting
3-pin XLR connectors are follows:
Building a serial DMX-chain:
Connect the DMX output of the first fixture with the DMX input of the
next fixture. And execute all the setups following the above-
Flip the DIP SWITCH #3 of last fixture to ON position for terminal
Connection with the mains
Connect the device to the mains with the power-plug.
The occupation of the connection-cables is as follows:
The earth has to be connected! In general, lighting effects should not
be connected to dimming-packs.
DMX Channel chart
Dimmer from dark to lightest.
Shutter from slow to fast.
Fade out fast to slow.
Fade in slow to fast.
Random shutter slow to fast
Reverse rotate from slow to fast.
Forward rotate from fast to slow.
From white to full cyan.
From white to full magenta.
From white to full yellow.
Zoom from 10 ~ 30
Flat and wide beam effect at 0°.
Flat and wide beam effect can 90° adjustment.
Y-axis fine tuning of
Pan/Tilt adjustment in the manual mode
(adjust nearness is moving rapidly).
Pan/Tilt adjustment in the auto movement
mode (adjust nearness is moving slowly).
X-axis fine tuning of
Make color wheel, cyan, magenta, yellow into
offset calibration status after 3 seconds.
(Pan coarse -> Offset color wheel * Tilt coarse ->
Offset cyan * Pan fine -> Offset magenta *
Tilt fine -> Offset yellow)
Save offset value after counter 3 seconds.
Reset whole motors after counter 3 seconds
Switch On the lamp after counter 3 seconds.
Switch Off the lamp after counter 3 seconds.
Replacing the Fuse
If the fixture does not function, that may be the fuse was burned out. It
may be time to replace the fuse of same type and specification for
eliminating this fault.
Remove the electric power and flip the switch to " off " position before
replacing the fuse.
Replace the fuse as follows:
Step 1: Unscrew the screw of the fuse holder on the housing
counterclockwise with appropriate tools.
Step 2: Remove the broken fuse and then replace the new fuse.
Step 3: Reinsert and tighten the screw on the fuse-holder.
Step 4: Turn the power on for test.
Please contact with the dealer if the fixture still cannot work or the fuse
burns out again.
AC input: Certified power cord with
plug or without plug
Voltage: Magnetic - 210/230/245V /
50Hz, 208/230V / 60Hz
Electronic ballast - 100/120
Fuse: 230V 7A, 110V 15A
Power Consumption: 800W
Lamp: 575W discharge
Approved models: Philips MSI-575/HR
(1000 hr; 6000K)
(1000 hr; 6500K)
(750 hr; 6000K)
Control: Automatic and DMX
Ballast: Electronic & magnetic
Control and programming
Signal pinout: pin 1 shield, pin 2 (-), pin 3 (+)
Setting and addressing: LED control panel
Protocol: USITT DMX-512
Pan/tilt resolution: 8 or 16 bit
DMX channels: 13-15
Signal input: 3-pin XLR male
Signal output: 3-pin XLR female
Cyan: 0-100% + offset adjustment
Magenta: 0-100% + offset adjustment
Yellow: 0-100% + offset adjustment
Color wheel: 6 colors, 3200
included + open + offset
Frost effect: Full beam, soft-edge frost
Flat & Wide: Beam shape adjustment 0
Dimmer/Shutter: Infinite dimming and
strobe 1~12 fps with
230V /27.5 kg, 110V /30.5 kg
Dimension (L x W x H):
416 x 400 x 564 mm