Full Text Searchable PDF User Manual
<鏂囨。鏍囬>
3
Table of Content
1 The Appearance of Product
...................................................... 4
1.1 Keypad instruction
......................................................... 4
1.2 Wall mount setup
........................................................... 6
2 Telephone Setting
............................................................... 7
2.1 Getting IP address
.......................................................... 7
2.2 Checking IP address
........................................................ 7
2.3 How to enter web setting interface
........................................... 7
2.4 How to set the memory key
.................................................. 8
2.5 Network setting
............................................................. 8
2.6 SIP setting
................................................................. 9
2.7 LED indicator state
......................................................... 9
3 Basic Operation
................................................................ 10
3.1 Making a call
.............................................................. 10
3.2 Answering a call
........................................................... 10
3.3 Holding a call
.............................................................. 10
3.4 Redialing
.................................................................. 10
4 Advanced Operation
............................................................ 11
4.1 Call transfer
............................................................... 11
4.2 Messages waiting
.......................................................... 11
5 FAQ
........................................................................... 12
<鏂囨。鏍囬>
4
1
The Appearance of Product
1.1 Keypad instruction
A: Telephone LED Indicator
The light flashes when the telephone rings for incoming calls. When the telephone system
supports Messages Waiting Indication (MWI) function and there are some voice messages,
the light will also flash.
B: Hold Button
Places a call on hold status.
C: Release Button
Hang up again after ending the active call
D: Transfer Button
Transfer a call to another number
E: Redial
Dial the last number you dialed.
<鏂囨。鏍囬>
5
F: Dial Pad
Dial the number you want.
G: Programmable Button
Stores phone numbers or feature access codes.
H: Handset LED Indicator
I: Power LED Indicator
J: Cable trough
K: Wan Port
L: Headset Port
Connect the headset cord.
M: Handset Wire trough
N: Wall Mount Hole
O: Power Port
(When use do not the power supply, please will the PVC stick in this position, prevent dirt or debris.)
P: PVC
<鏂囨。鏍囬>
6
1.2 Wall mount setup
Fix the device on the wall.
1.
Screw the embedded junction box on the wall
2.
Connect the cable from embedded junction box to the telephone.
3.
Hitch the telephone on the screw.
Please refer the dimension when you want to screw the embedded junction box on the wall.
10.7cm
Screw
Screw
Wall
Embedded junction box
8.5cm*8.5cm
5.8cm
13.2cm
<鏂囨。鏍囬>
7
2
Telephone Setting
2.1 Getting IP address
DHCP is the default network setting, and telephone will get the IP address from DHCP
server(Router) after the cable connected.
2.2 Checking IP address
Pick up the handset and long press the 鈥#鈥 key, then you can hear the IP address voice
information.
2.3 How to enter web setting interface
Set the telephone through web interface.
1. Connect the telephone and PC in the same LAN.
2. Run the IE in the PC, and input the telephone IP in address bar.
3. Input the use
r name and password, both of them are 鈥渁dmin鈥.
4.
Click 鈥淟ogon鈥 button to enter into the web setting interface.
<鏂囨。鏍囬>
8
2.4 How to set the memory key
Enter into the web setting interface, select
Function Key->Function Key.
Select the function and fill the number in the
Value
items.
2.5 Network setting
Enter into the web setting interface, select
Network->Basic,
there are three mode of network.
1
锛
Static IP
2
锛
DHCP
Get IP address from DHCP server automatically.
3
锛
PPPoE
PPPoE server, Username, Password
You should choose correct network mode according to your network environment.
<鏂囨。鏍囬>
9
2.6 SIP setting
Enter into the web setting interface, select
Line->SIP,
and fill in the items below.
1
锛
Server address
2
锛
Account name
3
锛
Phone number
4
锛
Password
Click the 鈥淎pply鈥 button to save the config, you can dial out after the register status is
鈥淩egistered鈥 with red color.
2.7 LED indicator state
Incoming call
The telephone LED indicator will flash at 0.5s on, 0.5s off.
MWI
The telephone LED indicator will flash at 0.5s on, 2s off.
Picking up the handset.
All buttons backlight will keep on.
Connecting power.
The power indicator will keep on.
<鏂囨。鏍囬>
10
3
Basic Operation
3.1 Making a call
There are two ways to make a call, using dial pad or memory button.
1. Off-hook
2. Dial the number on the dial pad or press memory key, end with # as default.
3. On-hook, end a call.
3.2 Answering a call
When your telephone rings and the telephone LED indicator will flashes.
1. Pick up the handset and start to talk.
2. Hang up, end a call.
3.3 Holding a call
1. While on a call, press the Hold key, the call will be held.
2. To retrieve a held call, you can press the Hold key again.
3.4 Redialing
Press the Redial key to dial the last number you dialed.
1. Pick up handset.
2.
Press 鈥淩edial鈥 key to dial the last number you dialed.
<鏂囨。鏍囬>
11
4
Advanced Operation
4.1 Call transfer
Blind transfer
During a call, you want to transfer the call to another one without talking with the one you
transfer to.
1.
Press 鈥淭ransfer鈥 key, you can get the second dial tone , and the first call is held
automatically.
2. Dial the number which you want to transfer to, and
then press鈥#鈥 or 鈥淭ransfer鈥 button.
3. When the third party answers the incoming call you will hear the busy tone, the call have
been transferred successfully.
Attended transfer
During a call, you want to transfer the call to another one after talking with the one you transfer
to.
1.
Press 鈥淭ransfer鈥 key, get the second dial tone, and the first call is held automatically.
2.
Dial the number you want to transfer to, press鈥淩edial鈥漦ey, the second call connected.
3.
Press 鈥淭ransfer鈥 key again, you will hear the busy tone, the call have been transferred
successfully.
4.2 Messages waiting
When the telephone LED indicator flashes and there is no incoming call, you need to dial
the feature access code for message retrieving. Once the messages have been retrieved, the
light flashing will stop. You can save your messages waiting feature access code on a memory
button, when you listen voice massages usually.
<鏂囨。鏍囬>
12
5
FAQ
1.
Line LIGHT indicator flashes, can鈥檛 make a call.
Please check the SIP register status, and make sure the register information is correct.
2.
Can鈥檛 hear the voice each other
Please contact your administrator to confirm whether there is firewall in the network.
3.
Can鈥檛 get IP address
Please contact your administrator to make sure the network setting is correct.
4.
Can鈥檛 visit the web setting interface
Please make sure all of connections are correct.
1) Check the IP address you input in PC.
2) Make sure the PC and telephone in the same LAN
3) Do factory reset and try again.