Combi-Cam miniK 10 Operating Manual - User Manual

Download PDF User Manual

Full Text Searchable PDF User Manual

OPERATING MANUAL

cabinets lockers carts

Combi Cam

electronic cam lock

SINGLE USER MODE

MULTIPLE USER MODE (LOCKER MODE / ONE TIME USE MODE)

SERVICE PASSWORD

MASTER PASSWORD

PROGRAMMING THE MINIK10

TECHNICAL SPECIFICATIONS:

LIGHT AND AUDIO NOTIFICATION:

MAINTENANCE:

GENERAL WARNINGS:

PROGRAMMING OPTION DEFINITIONS:

OTHER PRODUCTS IN THE COMBI-CAM FAMILY:

CHANGING THE BATTERY:

Page 2

INTRODUCTION:

Combi-Cam E – electronic cabinet lock with master/manager code, one-time-use functionality, and
up to 10 years battery life. Combi-Cam E can be installed for both right and
left hand installations – anywhere that needs ﬂexibility of master/manager
codes. The eco-friendly MiniK10 oﬀers both convenience of far less
frequent battery changes and a more
environmentally friendly solution.

PASSWORD LEVELS:

The Combi-Cam E has three potential password levels –
1. User password
2. Service password (must activate in Program 5.1)
3. Master password
The user and master passwords should be changed prior to installation and tested. Write down new
passwords and keep in a safe place. It is not possible to open lock if you forget your password.

MODES:

The Combi-Cam E can operate in two diﬀerent modes:
1. Single User (factory default)- Set password and user will open lock each time with same password.
2. Multiple User Locker Mode- user enters in their code when lock is in unlocked position, rotates
handle to lock. Upon returning uses same code to open. Next user can repeat the process with
their own unique password.

SINGLE USER MODE

OPENING WITH USER PASSWORD:

1) Enter your 4-digit user password. On ﬁrst
use factory default is <1-0-1-0>.
2) Rotate handle within 5 seconds to opening
direction and there will be a conﬁrmation beep.

CLOSING WITH USER PASSWORD:

1)Enter your 4-digit user password.
2) Rotate handle within 5 seconds so that handle
is toward warning label that displays lock is closed.
Lock will give a warning beep and the green LED
light will blink. NOTE: Program 6.1 allows lock to be closed without a password.

CHANGING USER PASSWORD:

If single user mode is selected (default), press button and enter current 4-digit user
password. Press button again and enter new 4-digit user password. Press button again and
approve new password. You will get a conﬁrmation beep and green LED light will blink.

vs.

Below illustrations show examples of lock installed for right
handed door. Lock can be installed for left or right handed.

MULTIPLE USER MODE (LOCKER MODE / ONE TIME USE MODE)

SERVICE PASSWORD

MASTER PASSWORD

OLD USER NEW USER

PROGRAMMING THE MINIK10

TECHNICAL SPECIFICATIONS:

LIGHT AND AUDIO NOTIFICATION:

MAINTENANCE:

GENERAL WARNINGS:

PROGRAMMING OPTION DEFINITIONS:

OTHER PRODUCTS IN THE COMBI-CAM FAMILY:

CHANGING THE BATTERY:

Page 3

SINGLE USER MODE

MULTIPLE USER MODE (LOCKER MODE / ONE TIME USE MODE)

In multiple user mode, opening and closing with a password process is same as Single User. However,
each time lock is in open position, each user can enter in their own unique 4-digit code
to lock and then open the MiniK10. Popular application is for gym lockers.

SERVICE PASSWORD

By default, service password is not active. Activate with Program 5.1.

Service password allows lock to be opened only and none of lock features can be programmed.

OPENING WITH SERVICE PASSWORD:

Default - <1-0-1-0-1>

If service password function is active, 1) press button and enter current 5-digit service password and
press button. 2) Rotate handle within
5 seconds to opening direction. You
will get a conﬁrmation beep from lock and
green LED light will blink.

CHANGING SERVICE PASSWORD:

When you have selected service password in program menu, press button twice and enter current
5-digit service password. Press button again and enter new 5-digit service password. Press
button again and approve
new password. You will get a
conﬁrmation beep from lock and
green LED lights will blink.

MASTER PASSWORD

opens lock and grants access to all programming features

OPENING WITH MASTER PASSWORD:

Default - <1-0-1-0-1-0>

1) Press the button and enter current 6-digit
master password and press button. 2) Rotate
handle within 5 seconds to opening direction.
You will get a conﬁrmation beep from lock and
green LED light will blink.

CLOSING WITH MASTER PASSWORD:

1) Press button and enter 6-digit master
password. Press button again.
2) Rotate handle within 5 seconds counter
clockwise, so handle faces padlock label indicating
lock is closed. You will get a conﬁrmation beep from lock.

CHANGING MASTER PASSWORD:

Set new master password and test BEFORE installing lock.

Press button twice, and then enter old 6-digit master password. Press button again and
enter new 6-digit master password. Press button again and approve new password.
You will get a conﬁrmation beep from lock.

SERVICE PASSWORD

OLD SERVICE NEW SERVICE

MASTER PASSWORD

OLD MASTER NEW MASTER

PROGRAMMING THE MINIK10

TECHNICAL SPECIFICATIONS:

LIGHT AND AUDIO NOTIFICATION:

MAINTENANCE:

GENERAL WARNINGS:

PROGRAMMING OPTION DEFINITIONS:

OTHER PRODUCTS IN THE COMBI-CAM FAMILY:

CHANGING THE BATTERY:

Page 4

SINGLE USER MODE

MULTIPLE USER MODE (LOCKER MODE / ONE TIME USE MODE)

SERVICE PASSWORD

MASTER PASSWORD

Prg No 1-1: One -time-use operation (Locker mode with multiple users)

Prg No 2-1: Audible beeps and conﬁrmations

Prg No 3-0: Penalty operation is not active
Prg No 4-0: No function currently assigned

Prg No 5-0: Service password is not active
Prg No 6-0: Closing with password required

Prg No 7-0: Warning of open door is not active

Prg No 8-0: Resetting user password is not active
Prg No 9-0: Blocking of the lock is not active

Individual operation

One -time-use operation (locker mode for multiple users)

Mute operation except for warnings

Audible operation- button feedback, warnings and conﬁrmations

Penalty not active

Penalty

active (lock blocked for 5 minutes if wrong code entered 3 times)

None

Service password is not active

Service password is active

Closing with password is active

Automatically closing is active (for individual usage)

Warning of door open is not active

Warning of door open is active (beeps 8 times every 5 seconds)

Resetting user password is not active (if service password is active)

Resetting user password is active (if service password is active)

Blocking of the lock is not active (if service password is active)

Blocking of the lock is active after using service password (if it is active)

PROGRAMMING THE MINIK10

The MiniK10 can be customized from factory default settings tailored to your needs.

ACCESSING THE PROGRAM MENU:

Press the button and then enter the 6-digit master password. Press the button. Press the
program number that you will make an adjustment to, and then press the adjustment selection.

PROG.
NO

SELECTION
NO

MASTER PASSWORD

Program No

Selection No

Explanation:

0-1

Restores factory default settings:

TECHNICAL SPECIFICATIONS:

LIGHT AND AUDIO NOTIFICATION:

MAINTENANCE:

GENERAL WARNINGS:

PROGRAMMING OPTION DEFINITIONS:

OTHER PRODUCTS IN THE COMBI-CAM FAMILY:

CHANGING THE BATTERY:

Page 5

SINGLE USER MODE

MULTIPLE USER MODE (LOCKER MODE / ONE TIME USE MODE)

SERVICE PASSWORD

MASTER PASSWORD

PROGRAMMING THE MINIK10

TECHNICAL SPECIFICATIONS:

LIGHT AND AUDIO NOTIFICATION:

Password is accepted:

Green LED lights with two repeated audio warnings

Wrong password:

Red LED lights with four repeated audio warnings

Low battery:

Red LED lights blink 5 times after each operation

Lock is open:

1 minute after door is opened, lock gives audible warning 8 times

every

seconds

MAINTENANCE:

GENERAL WARNINGS:

Restoring factory settings:

All factory default settings are restored (see

program menu). User password becomes <1-0-1-0> and master password
becomes <1-0-1-0-1-0>.

Individual Use or Locker Mode:

Factory default is locker mode (one time

use) whereby each user that walks up to an open MiniK10 can enter their 4-
digit code to close and open lock.  Every person can enter their own new code
when lock is in open mode.  Individual use mode allows one 4-digit static code
to be entered that would remain same code for one user.

Audible volume control:

All audio warnings can be turned off if mute

operation is selected (except warning beeps).

Penalty operation:

Prevents tampering of lock by unauthorized people. Lock

is blocked for 5 minutes if wrong password is entered three times
consecutively. Factory default is that this feature is not active.

This programming function is currently open for placing a future feature

Service password:

Lock can be opened with service password if user

password is forgotten. Factory service default password is <1-0-1-0-1>. No
programming features can be accessed with service password. Factory
default is that this feature is not active.

Closing modes:

Factory default is that the MiniK10 requires a password to

lock. The other option is it can be locked without requiring a password.

Door open warning:

After door is open for one minute, lock gives an audible

warning to user with 8 beeps every 5 seconds to notify user that the door has
been left open.

Resetting user password:

If the lock is opened with service password (and

service password is active), user password can be reset. (see program #5 on
service passwords). Factory default is that the service password access does
not allow the user password to be reset (only opens up the lock).

Blocking the lock:

If lock opened with service password, it can be blocked

from further user password access

This would insure service password is only

used to access locks for emergency lockouts. Master password access would
then be required to set up user password again (0-1 Factory default reset).
Factory default is that this feature is not active.

PROGRAMMING OPTION DEFINITIONS:

OTHER PRODUCTS IN THE COMBI-CAM FAMILY:

CHANGING THE BATTERY:

Lock operates on a 3V lithium coin cell CR2450 battery located on back side of device. Remove screw
located on cover of battery and replace it with new battery. Battery life is up to 10 years. Th red LED
light blinks 5 times after each operation when battery is low and it is possible to open and close
lock for 100-150 times after you get the initial low battery warning.

Page 6

SINGLE USER MODE

MULTIPLE USER MODE (LOCKER MODE / ONE TIME USE MODE)

SERVICE PASSWORD

MASTER PASSWORD

PROGRAMMING THE MINIK10

TECHNICAL SPECIFICATIONS:

LIGHT AND AUDIO NOTIFICATION:

MAINTENANCE:

- Clean front of lock with a mild damp cloth with detergent if needed.

- Do not use any hard or scratching cleanser.

- Do not clean with chemical materials that melt plastic (e.g. thinner, acetone, etc.)

-Be careful not to spill water on lock.

GENERAL WARNINGS:

- Read manual before using lock.

- Set and test user and master passwords prior to installing the lock

- Change all default passwords with your own passwords.

- Common sense, but we must say it... Do not keep the passwords in the cabinet where

the lock is being installed!

- It is not possible to open lock if installed and you forget the user and master password.

- Lock gives a warning beep when passwords are old or have not been entered excessively.

- Not possible for front side of lock to be opened by breaking or trying to force open lock.

- Use CR2450 3.0V Lithium batteries.

- Remember that battery consumption is high when programs 2, 3, and 7 are active.

PROGRAMMING OPTION DEFINITIONS:

OTHER PRODUCTS IN THE COMBI-CAM FAMILY:

CHANGING THE BATTERY:

Installation instructions??
- Cam placement,
- Stop Cam
- Template for screw hole?
- Template for routing out?
- Optional Cams available?
- What about metal semiflush mount? Is there a bracket available?

Combi Cam

NOTE:
These are default
settings by the
factory. Once they
are changed, be
sure to right down
your new code !

QUICK INFO

SINGLE USER MODE

MULTIPLE USER MODE (LOCKER MODE / ONE TIME USE MODE)

SERVICE PASSWORD

MASTER PASSWORD

PROGRAMMING THE MINIK10

Page 7

TECHNICAL SPECIFICATIONS:

LIGHT AND AUDIO NOTIFICATION:

MAINTENANCE:

GENERAL WARNINGS:

PROGRAMMING OPTION DEFINITIONS:

OTHER PRODUCTS IN THE COMBI-CAM FAMILY:

CHANGING THE BATTERY:

Opening direction varies according to type of door MiniK10 is installed.
All opening illustrations depict right handed door installation.

18424 HWY 99
Lynnwood WA 98037

www.fjmsecurity.com

Toll Free: 800-654-1786
Fax: 206-350-1186

F J M

Security Products

Innovative, Quality Security Solutions

Page 8

SINGLE USER MODE

eco-friendly

electronic lock

Combi Cam

Batteries don’t just grow on trees you know!

Install Green

For more detailed instructions and
video demos, go to www.combi-cam/E/

MULTIPLE USER MODE (LOCKER MODE / ONE TIME USE MODE)

SERVICE PASSWORD

MASTER PASSWORD

PROGRAMMING THE MINIK10

NOTE:

Remember to write down your passwords after programming and prior to

installing lock. It is not possible to open lock if it is installed and you forget your passwords.

Battery:

3.0V Lithium CR 2450

Key Pad:

Silicone Keypad

Operating Temperature:

-5 / 55 C

Storage Temperature:

-10 / +70 C

Operating Moisture:

20 – 80% Rh (without condensation)

TECHNICAL SPECIFICATIONS:

LIGHT AND AUDIO NOTIFICATION:

MAINTENANCE:

GENERAL WARNINGS:

PROGRAMMING OPTION DEFINITIONS:

OTHER PRODUCTS IN THE COMBI-CAM FAMILY:

www.combi-cam.com

™

CHANGING THE BATTERY: