Ardwolf A30 User Manual - User Manual

Download PDF User Manual

Full Text Searchable PDF User Manual

Ardwolf A30 Keypad Door Lock

User Manual

Customer Service

Email: service@ardwolf.com

Address: 12240 East End Ave Chino CA 91710 United States

www.ardwolf.com

Dimension: 6.0 X 3.1 X 2.7 inch
Material: Zinc Alloy
Weight: 5.1 lbs

Sensor Area

Keypad

Front Handle

Front

Lock Bolt

Side

Back Handle

Back

Switch Button

Product Introduction

Content

Product Introduction

---------------------------------------------------------- 01

1. Product Features -------------------------------------------------------------- 02

2. Product Specifications ------------------------------------------------------- 03

3. Packing List -------------------------------------------------------------------- 04

Installation Guide

--------------------------------------------------------------- 05

1. Installation Conditions ------------------------------------------------------- 05

2. Installation Tools -------------------------------------------------------------- 06

3. Drill Holes On Door ---------------------------------------------------------- 06

4. Installation Steps ------------------------------------------------------------- 07

Programming

-------------------------- ------------------------------------------08

1. General Information ---------------------------------------------------------- 08

2. Functions Detail -------------------------------------------------------------- 12

Standard 12-key keypad
Fit door thickness between 1.38” and 1.77”
Factory default user code is “123456.” The fixed length of

master password is 6 digits
Engineering password is fixed at “0”. After modifying the

master password, engineering password will be disabled.
Service code is any number between 1-6 digits
The fixed length of temporary master password is 14 digits
Card Type: Mifare S50 Card
Reading Distance: appr. 2.5cm/1’
Powered by 4 AA alkaline batteries (NOT included)
NOT warterproof
Static Power: 30uA
Dynamic Power: 200mA

2. Product Specifications:

Three ways to unlock: User Code, Mifare Card or Key.
Up to 200 user codes can be programmed into the lock.

(user code is between 4-8 digits )
Up to 200 Mifare Card can be programmed into the lock.
Up to 10 service codes can be programmed to each lock

for special purpose, service code can only grant one time

access.
Scheduling can be programmed, usage restriction policy

can be set between time periods for both user code and

mifare card.
Automatic locking: for each valid entry, lock will

automatically lock in 5 sec.
Reversible lever: fits both left-handed and right-handed

doors.
Trial and Error Protection improves safety in the application

environment
Normal open/cancel operation makes it easy for users to set

up and cancel
Multi-level management functionality allows users to

locate/delete user info in the lock’s internal memory, suitable

for different application environments

1. Product Features

1. Installation conditions

1.1 Door Thickness Requirements

Door frame≥110mm (for Inconsistent door thickness )

35mm≤Door Thickness≤45mm (More Than 45mm Need

To Custom Accessories)
1.2 Confirm The Direction of the door

Installation Guide

Interior

Door

Wall

Interior

Door

Door Open Direction

Door

Wall

1. Front Panel

2. Back Panel

3. Waterproof Rubber Pad

4. Inside Chassis

5. Lock Bolt

6. Bolt Protector

7. Wrench

8. Strike Plate

9. Square Spindle

10. Pin (for square spindle fixing)

11. Mechanical Key

12. Fixing Screw x4 (A)

(for strike plate fixing)

13. Fixing Screw x 3 (B1)

Fixing Screw x 3 (B2)

Use B1 or B2 for fixing,

depends on door thickness

14. Screw x 1 (C)

(for front panel fixing)

15. Screw x 2 (D)

(for front panel fixing)

16. Screw x 2 (E)

(for back panel fixing)

17. Screw x 1 (F)

(for the screw “C” fixing)

18. User Manual

20. Hole Drilling Template

How to adjust the direction of lock handle

Front Panel
1. Remove the 8 small screws

2. Take out the mechanical system

slightly. Do not damage the wire.

3. Remove the screw holding the

handle, then adjust the handle

direction as desired

4. Assemble the screws back

Back Panel
1. Remove the screws holding the

handle, adjust the handle

direction as desired

2. Assemble the screws back

screw position

19. Mifare Card x 2

3. Packing List

2. Installation Tools

3. Drill Holes On Door

Below is the Drill Holes Template

∅

20
3

Handle Centerline

1. Pencil

2. Tape Measure

3. Square Measure

4. Power Drill

5. Drill Bits

6. Hammer

7. Utility Knife

8. Phillips Screwdriver

9. Chisel

4. Installation Steps

1. Draw lines

a. To draw a horizontal

centerline on both sides of

the inner and outer door one

meter from the ground.
b. Fold Drill Holes Template,

align the handle centerline

with the horizontal line on the

door, draw the front and side

drill holes lines according to

the requirements of the Drill

Holes template.

3. Install Latch

Install the latch to the hole,

and fix it by using two “A”

screws.

2. Drill Holes

Drill Holes on the door

according to the requirements

of the Drill Holes template

4. The front panel installation

a. Connect the screws of “C” and “F”, then fix it

in the hole which be showed on the front panel

b. Fix the screws of “D” on the front panel

c. Insert the square spindle, fix it by the “pin” which

get through the small hole in the spindle and the

front panel. Be sure to bend the pin for fixing.

d. Put on the waterproof rubber pad

e. Align the cylinder holes, install the front panel.

The wire get through from the main hole.

a. Put on the waterproof rubber pad, get the

wire through from the “wire hole” which on

the inside chassis.

b. Install the inside chassis, fixing it by using

screws of “B1” or “B2” which

depends on the thickness of

the door.

c. Connect the wire to the

hub on the inside chassis.

5. The inside chassis installation

6. Install the battery and back panel

7. Installation Test

a. Check the flexibility of

outside and inside handle
b. Check if the Mechanical

keys works

8. Strike installation

Screw"B1" or "B2"

Wire Hole

screw A

screw C

screw D

square spindle

a. Install 4 AA Alkaline batteries.

b. Fixing the back panel by two screws of “E”

Install the bolt protector and strike plate, fixing

by using 2 screws of “A”

Exit setting mode:

Enter * to exit the setting procedure, or

wait for 10 seconds

Low battery warning:

When the voltage drops below 4.8V,

after entering a valid code, the LED will flash red and beep

five times.

Unlocking indicator:

Green light will flash and beep twice.

Locking indicator:

Red light will flash and beep three

times.

Reset:

Set the lock back to manufacturer default. Press

and hold the reset button for about 10 seconds (3 beeps

with LED blink red). The reset button is located below the

battery compartment. (See Picture)

Programming

General Information

Reset Button

Daylight Savings:

Disabled

Auto unlock/lock:

Disabled

Default programming code:

123456

Lock mode:

Storehouse

Construction code:

0 #

Manufacturer default settings

a. Change master code (For example, change to 1234)
# 123456 # 11 # 1234 # 1234 #

b. Enable daylight saving (optional)
# 1234 # 31 #

c. Set lock time (optional) (For example, set time as January

23, 2008, 2:45PM)
# 1234 # 88 # 0801231445#

d. Add user code (For example, add 1357 to the lock, 001 is

index No.)
# 1234 # 01 # 001# 1357 # # #

e. Add user card (Optional.002 is index No.)
# 1234 # 01 # 002 # touch MF card onto reader ## # (wait

light goes off)

Steps to setup a new lock (please follow the order)

Set schedule for user code or user card (see 29 How to

program schedule week & time)

Key code:

User Code, #

Key card:

Card key touch lock reader

Key card +Key code:

card touch lock reader, LED grow

green, enter user code, #

One time service code:

One time code, #

Mechanical key:

Turn the override key 90 degree

clockwise, then turn the handle

Different methods to operate the lock

Master code:

The master code puts the lock into a

programming mode. It won’t lock/unlock the lock. When # sign

is pressed, the red LED will start to flash indicating the lock is

now in programming mode. If more than 6 seconds have

passed in between programming entries, the lock will return to

normal operational status. For maximum security it is

recommended to change the default Master Code.

Construction code:

Installer code is a default temporary

code (0) for installer to testing the lock. The code will be

deleted after the first new user code is added to the lock.

User code:

User code is the normal code for day-to-day

operations.

Service code:

Service codes are used for special purposes

such as maintenance personnel or vendors. Service code

only grants one time access. Total of 10 sets of service codes

can be programmed to each lock.

Terms

Index No.*:

For each user code or user card. It is associate

with a unique number, we call it index No. (or slot No.). The

Index No. is auto generated by lock and starts with 001. The

highest Index No. will be 200. Total user index is 200 that can

be added to each lock. (* Please log the user code along with

its index No. for adding or deleting references)

Passage mode:

When Passage Mode is enabled, the lock

will stay in unlocked status after first valid entry. Enter a valid

entry code to lock back the door.

Storehouse mode (Lock-back mode):

For each valid entry,

lock will automatically lock in 5 seconds.

Lockout mode:

Enable the Lockout mode will freeze the lock

at its current status (Lock or unlock), temporarily disable all

the user codes and user code. Re-enter the function code 99

to disable the lockout mode, and resume normal operation.

Reset lock memory:

Press and hold reset button for about

10 seconds with 3 short beeps; it will delete all the codes,

cards, and restore back to factory default setting.

Time format:

0830 = 8:30AM; 1730 = 5:30PM

Schedule Date:

1=Mon, 2=Tue, 3=Wed, 4=Thu, 5=Fri, 6=Sat,

7=Sun

1. How to change master code (but not delete existing

users)

▲

Function Code: 11#

{#}+{default master code#}+{11#}+{new master

code#}+{new master code#}

2. How to change master code (and delete all existing

users)

▲

Function code: 22#

{#}+{current master code#}+{22#}+{new master code#}

+ {new master code#}

3. How to enable daytime saving function

▲

Function Code: 31#

{#Master code#}+{31#}

4. How to set date and time

▲

Function Code: 88#

{#Master code#}+{88#}+{yymmddhhmm#}

5. How to add one user code (no time restriction)

▲

Function Code: 01#

{#Master code#}+{01#}+{index No. #}+{user code# # #}

6. How to add multi-user code (no time restriction)

▲

Function Code: 01#

{#Master code#}+{01#}+{index No. #}+{user code(1)# #

#}+{index No. #}+{user code(2)# # #}+{index No. #}+{user

code3###} … and more if needed

Functions Detail

7. How to add one user access code (with time

restriction)

▲

Function Code: 01#

{#Master code#}+{01#}+{index No. #}+{user code#}+

{yymmddhhmm#(start time)}+{yymmddhhmm#

(ending time)}

8. How to add multi-user code (with time restriction)

▲

Function Code: 01#

{#Master code#}+{01#}+{index No. #}+{user

code#(1)}+{yymmddhhmm#(start)}+{yymmddhhmm#

(ending time)}+ {index No. #}+ {user code#(2)} +

{yymmddhhmm#(start)} + {yymmddhhmm#(ending)} …and

more if needed

9. How to add one user card (no time restriction)

▲

Function Code: 01#

{#Master code#}+{01#}+{index No. #}+{touch card # #}

10. How to add multi-user card (no time restriction)

▲

Function Code: 01#

{#Master code#}+{01#}+{index No. #}+{card (1)# #}+{index

No. #}+{card (2)# #} …and more if needed

11. How to add user code + user card as dual user (no

time restriction)

▲

Function Code: 01#

{#Master code#}+{01#}+{index No. #}+ {user

code#}+{touch card # #}

12. How to add one user card (with time restriction)

▲

Function Code: 01#

{#Master code#}+{01#}+{index No. #}+ touch {card}+

{yymmddhhmm#(start time)}+{yymmddhhmm#(ending

time)}

13. How to add multi-user card (with time restriction)

▲

Function Code: 01#

{#Master code#}+{01#}+{index No. #}+ touch {card (1)}+

{yymmddhhmm#(start time ) } + {yymmddhhmm#(end

time)} +{index No. #}+ touch {card (2)} +

{yymmddhhmm#(start)}+ {yymmddhhmm#(end time)}

…and so on

14. How to disable one user code or user card with index

No.

▲

Function Code: 02#

{#Master code#}+{02#}+{index No.#}

15. How to enable one user code or user card with index

No.

▲

Function Code: 03#

{#Master code#}+{03#}+{index No.#}

16. How to enable passage mode and schedule (lock back

when the passage mode end)

▲

Function Code: 15#

{#Program#}+{15#}+{weekly schedule}+{#}+{begin time &

ending time#}

17. How to disable passage mode

▲

Function Code: 16#

#Master#}+{16#}

18. How to enable LED blink light (on & off)

▲

Function Code: 18#

{#Master code#}+{18#}

19. How to disable daytime saving

▲

Function Code: 32#

{#Master code#}+{32#}

20. How to set up one time service code (up to 10 service

codes)

▲

Function Code: 33#

{#Master code#}+{33#}+{service code(1)#}+ {service

code(2)#}+… and so on

21. How to delete all one time service codes

▲

Function Code: 23#

{#Master code#}+{23#}

22. How to delete user code or user card with index #

▲

Function Code: 44#

{#Master code#}+{44#}+{index#}

23. How to enable auto-unlock function

▲

Function Code: 64#

{#Master code#}+{64#}

24. How to setup auto-unlock time (it will auto unlock the

door everyday at assigned time)

▲

Function Code: 63#

{#Master code#}+{63#}+{HHMM#}

25. How to disable auto-unlock function

▲

Function Code: 65#

{#Master code#}+{65#}

26. How to enable auto-lock function

▲

Function Code: 67#

{#Master code#}+{67#}

27.How to setup auto-lock time (it will auto lock the door

everyday at assigned time)

▲

Function Code: 66#

{#Master code#}+{66#}+{HHMM#}

28. How to disable auto-lock function

▲

Function Code: 68#

{#Master code#}+{68#}

29. How to enable / disable Lock-out mode (lock out all

the users if enabled)

▲

Function Code: 99#

{#Master#}+{99#}

30. How to program scheduling by week & time

▲

Function Code: (45#)

enable daylight saving

set up date & time (use 88# function code)

adding user code or user card in advance (see No.5 or

No.9 how to add user code & user card)

program schedule (as below example)

Weekly Schedule Format

Sun

Mon

Tue

Wed

Thu

Fri

Sat

Formula:

{#master code#}+{function code#}+{user code#

or card}+{weekly schedule day#}+{begin time & ending

time#}

How to schedule with a “User code”

Example: schedule for user code “2222” which will grant

access Mon., Wed. and Fri., from 8:30AM to 5:30PM

#1357#

45#

2222#

135#

0830

1730#

Master

code

Function

code

User code

Schedule

Beginning

time

Ending time

How to schedule with an “User card”

Example: schedule for user card which will grant access

Mon., Wed. and Fri., from 8:30AM to 5:30PM

#1357#

45#

Card#

135#

0830

1730#

Master

code

Function

code

Card

Schedule

Beginning

time

Ending

time

How to schedule with “User-code + user card”

Example: schedule for code “1357” + card which will grant

access Mon., Wed. and Fri., from 8:30AM to 5:30PM

#1357#

45#

2222# +

card

135#

0830

1730#

Master

code

Function

code

User code +

user card

Schedule

Beginning

time

Ending

time

How to schedule passage mode (also see number 16.)

Example: schedule passage mode Monday to Friday,

8:30AM to 5:30PM

#1357#

15#

12345#

0830

1730#

Master

code

Function

code

Schedule

Beginning

time

Ending time