PDF User Manual

  1. Home
  2. Manuals
  3. Agam AIT 501 User Manual

Agam AIT 501 User Manual

Made by: Agam
Type: User Manual
Category: Test Equipment
Pages: 2
Size: 10.81 MB

 

Download PDF User Manual



Full Text Searchable PDF User Manual



background image

It is recommended to select the specific 8pcs 

When charging battery is applied, the charging battery 

work mode should be selected at the startup: 

Insulation Resistance Tester

1 pc
1 pc

1 pc

1 pc

1 pc
1 pc
1 pc
1 pc

8 pcs

One-plug

Two-plug

chargeable batteries (LR14) and a charger. 

damaged part,

measurement requirement: Pollution Degree 2, 

Overvoltage Category(CAT. III 600V) and Double 

Insulation.  

alerts the user to avoid electric shock.

affect

test

leads and power adaptor with the same 

model or identical electrical specifications.

Low Battery Indication

after 15 minutes' inactivity.

There is a battery indicator shown on the upper left 

corner of the display. Please refer to Table 3 for 

detailed explanation.

almost

necessary. Under this status, the Meter 

can still output 500V and 1000V to 

measure, the measured accuracy will 

not be affected.

 hold USB button prior to startup, then press down ON/

OFF, LCD screen will display CHA or GEN, and select 

to display CHA by pressing the up/down key, after 

pressing USB key to confirm, the Meter successfully

enters the charging battery work mode. GEN means

the general alkaline battery work mode.

Press and

Two-plug

One-plug

One-plug

(Connected to one-plug test lead)

(Connected to one-plug black test lead)

( Connected to two-plug red test lead )

(Connected to two-plug red test lead)

voltage input terminal

Arrow Button

Arrow Button

Arrow Button

Arrow Button

The Meter defaults at 500V range and 

under continuous measurement of 

insulation resistance when turned on. 

LIGHT

Press to turn on/off the backlight.
Press to clear the saved data.

value. The Meter can save up to 18 sets.

previous 

voltage range.

next voltage

range.

setting the timer for the

When compare function is enabled for 

insulation resistance measurement, 

values

setting the timer for the

When compare function is enabled for 

insulation resistance measurement, 

values

Press

measurements

This

The Meter defaults at

500V range and under continuous measurement of 

insulation resistance when turned on.

AIT 501 USERS MANUAL

AIT 501 Smart Digital Insulation Tester

AIT 501 Smart Digital 

 


background image

This operating manual is subject to change without notice.

*END*

Insert the red test lead into two

 LINE 

terminals,

 

the black one into

 GUARD 

and the green one

 

into

 EARTH.

-

1

14

Caution

test leads into 

EARTH

 

and two 

LINE

 terminals.

 present on the red test lead,

if negative voltage is

output

cause 

measuring resistance 

2MΩ with use of 500V.

measuring resistance 

5MΩ with use of 1000V. 

measuring resistance 

10MΩ with use of 2500V.

measuring resistance 

20MΩ with use of 5000V.

voltage range.

green

outputs

Choose one of insulation resistance measurement 

modes shown as below:

personal injury.

carry out begin and output insulation resistance 

test voltage

turn off the voltage output,

the

the test voltage 

output will be turned off,

the test

voltage output will be turned off and the

step

readings.

Calculation Tips:

PI = 3-minute ~ 10-minute resistance/30-second ~ 

1-minute resistance

You can choose compare from:

compare value.

See Figure 6 for the use of power adaptor.

Using Power Adaptor

Figure 6. Using Power Adaptor

Connecting USB Interface

See Figure 7 for USB interface connection.

General Specifications

18 sets

Test Voltage

Automatically source the voltage.

Preset the timer for

two points and the Meter will carry out the measurement automatically.

B. Insulation Resistance Measurement

less

Marketed by:
RISHABH INSTRUMENTS PVT.LTD.
F-31, MIDC, Satpur, Nashik-422 007,India.
Tel.: +91 253 2202028, 2202202 Fax : +91 253 2351064
E-mail : India :- marketing@rishabh.co.in
International :- exp.marketing@rishabh.co.in
www.rishabh.co.in

AIT 501 USERS MANUAL

AIT 501

AIT 501

AIT 501