PDF User Manual

  1. Home
  2. Manuals
  3. A2Z Ozone Systems Aquatic 2 Installation & Operation Manual

A2Z Ozone Systems Aquatic 2 Installation & Operation Manual

Made by: A2Z Ozone Systems
Type: Installation & Operation Manual
Category: Inverter
Pages: 13
Size: 0.38 MB

 

Download PDF User Manual


Related Product Video

 

Full Text Searchable PDF User Manual



background image

A2Z Ozone, Inc. 

PRODUCT 

MANUAL

INSTALLATION & OPERATION MANUAL

CE

www.a2zozone.com

Rev. 02142018

 


background image

• Important Safety Instructions .........

• Specifications ...................................

• Installation Instructions ..................

• Troubleshooting .................................

• Warranty ...........................................

Page

3

4

5

11

12

CONTENTS

2

 


background image

IMPORTANT SAFETY INSTRUCTIONS

3

1. 

All electrical connections should be made by a qualified electrician.

2. 

Follow all applicable electrical codes.

3. 

Be sure the electrical power is shut OFF at the main circuit breaker before installing the Aquatic 2.

4. 

If the Aquatic 2 electrical connection will be attached to the spa controls, be sure the spa controls 

are protected by Ground Fault Circuit Interrupter (GFCI).
5. 

If the Aquatic 2 is connected to an independent electrical supply, a GFCI must be installed between 

the ozone generator and the electrical supply.
6. 

Do not bury cord.

7. 

WARNING – To reduce the risk of electrical shock, replace a damaged cord immediately.

8. 

Per UL spa requirements, the ozone generator must be mounted indoors or under a cover to ensure 

it is sheltered from the elements (rain, sun, sprinklers).
9. 

Mount the Aquatic 2 so that it is inaccessible to anyone in the spa. Never attempt servicing when 

wet.
10. 

To reduce the risk of injury, the unit should be mounted where it is inaccessible to children.

11. 

Plastic ozone supply tubing is available with the Aquatic 2

12. 

Never replace this tubing with metal tubing.

13. 

Do not operate the Aquatic 2 unless sufficient air flow is being drawn through the unit.

14. 

WARNING – Short term inhalation of high concentrations of ozone and long-term inhalations of low 

concentrations of ozone can cause harmful physiological effects. Do not inhale ozone gas produced by the 
device. 
15. 

PLEAE SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE

Proper installation and usage of your Aquatic 2 Spa Ozone Generator is your responsibility. 
Read and follow this owner’s manual carefully for important installation, operation and 
safety information. Basic safety precautions should always be followed, including but not 
limited to the following:

 


background image

SPECIFICATIONS

4

Model

Aquatic 2

Electric

85-250 VAC 50/60 Hz

Power

6w

Ozone Output

300 mg/hour

Size

3.6 x 2.5 x 5.7 inches
92 x 62 x 146 mm

Weight

0.74 lbs, 330 grams

Connection

AMP model

Cable

5.5 feet

Check Valve

1/4 inch

 


background image

INSTALLATION INSTRUCTIONS

5

How the Aquatic 2 Works

Installation Tools and Materials

Installation Parts

Unit Assembly

Mounting

The Aquatic 2 produces ozone gas which is introduced to spa water through suction 
created by a spa injector. The provided tubing is used to connect the Aquatic 2 to an 
injector or vacuum port provided by the spa manufacturer. The injector ports are vacuum 
sources used to pull the ozone gas out of the Aquatic 2 and into the water. Please keep 
in mind, at no time should water come in contact with the Aquatic 2. The unit must 
be mounted and plumbed as described in this manual to prevent water from traveling 
backwards through the tubing and into the ozone generator.

• 

1 installation manual

• 

1 check valve

• 

2 screws and plastic anchor for mounting

• 

4 hose ties

• 

5 feet of tubing

• 

Phillips screwdriver

• Pliers

• 

The Aquatic 2 is pre-assembled and ready to install

• 

Mount the Aquatic 2 as high as possible within the spa’s protected equipment area 

or outside.
• 

Screws are provided for mounting but may not be appropriate for all surfaces. 

Please substitute proper mounting hardware as required.

 


background image

6

Plumbing -- Vacuum System (refer to Figure 1)

Plumbing -- Ozone Generator (refer to Figure 1)

• 

Most spas are factory equipped with an ozone injector or vacuum port (like the one 

displayed in Figure 1).
• 

Review your spa’s installation manual to identify the correct ozone connection 

location.
• 

If the spa is not equipped with an injector (vacuum source), A2Z Ozone Systems 

provides a wide range of optional installation kits. Contact A2Z Ozone Customer Service 
for assistance at 502-499-4977.

• 

Connect shorter PVC ozone tube provided (8 inches) to the hose barb on the Aquatic 

2 side.
• 

Connect other end to the check valve.

• 

Connect longer PVC tube to injector suction.

• 

Be sure to run the spa and pump to check the vacuum BEFORE connecting the PVC 

tube to the injector.
• 

If there is no vacuum at suction, then you need to check the injector or pump water 

flow.
• 

Do not connect the Aquatic 2 if there is no vacuum at injector suction.

NOTE: If the Aquatic 2 is mounted below the water line, run the tubing to a point above the 
water line and back down to the vacuum source. Secure the tubing in this position, slide 
the hose ties on each end into the tubing and secure all tubing connections with the hose 
ties.

 


background image

7

Figure 1

 


background image

8

Safety Information

Please make sure water will not back up into the unit before use. Water will damage 
internal components of the unit, and will not be covered by the unit’s warranty. Please 
follow these steps when installing your unit:

1. 

Install the unit above water level and as high as possible.

2. 

Mount the unit so the tube, light and wires are toward the ground (disregard the 

front label).
3. 

Install the check valve according to the arrow on the check valve.

 

a. The arrow should face toward the injector.

4. 

You will need an injector for injecting ozone into the water line. If you do not have an 

injector, please contact us to purchase one. The unit does not work without an injector.
5. 

At this point, a vacuum should be created and the suction can be felt on the tube.

6. 

The Aquatic 2 should be on ONLY when the pump is ON. If your spa did not have an 

ozonator, then connect the ozone electric wire to the pump wires.

Figure 3

Installing the Aquatic 2 

 


background image

9

Figure 2

Electrical

1. 

Test the GFCI breaker protecting the spa for proper operation.

2. 

Disconnect power to the spa.

3. 

Connect the Aquatic 2 cord to the mating connector(s) on the spa control box as 

described in the spa’s installation manual and Figure 2.
4. 

Where possible, route the power cord away from other electrical lines. Do NOT run 

the power cord parallel to any low voltage signal wires.
5. 

Secure the power cord as required to prevent damage. 

1.

Withthespafilledtotheproperlevel,runthespacontrollerthroughseveralcycles.

2. 

Verify that the Aquatic 2 turns on and off as required by the controller.

3. 

The red LED light will be visible from the viewing window on the bottom left.

4.

Verifythatgasisflowingintotheinjector(thereshouldbenowaterinthetubingand

very small bubbles entering the spa through the return).
5. 

Verify that water does not push past the check valve during any spa cycle.

6. 

Check for and correct any leaks.

Operation

 


background image

10

Maintenance

Once properly installed, the ozone generator requires no further maintenance. It will 
operate automatically with the spa system. 
To ensure the highest degree of sanitation at all times, refer to the chart below. Renew 
your Aquatic 2 as needed with a renewal kit.

Daily Use

Average Unit Life

2 hour/day ozone cycle

3 years

3 hour/day ozone cycle

2 years

6 hour/day ozone cycle

1 year

 


background image

11

SYMPTOM: Cloudy water conditions even though the unit appears to be operating properly.

SYMPTOM: Water is backing into the ozonator when the system is ON or OFF.

SYMPTOM: The red LED light is not lit.

When your system is in its ON cycle, a suction of air is being pulled through the tubing 
from the ozonator to the return line. When the system is in its OFF cycle, water tends 
toflowbackinthetubingtowardtheozonator.Therefore,mountingyourozoneunitas
high as possible in relation to the spa water level is important. There is also a one-way 
checkvalveprovidedtopreventthebackflowofwaterfromreachingtheozonator.Asa
secondary precaution, a Hartford Loop in the tubing will help prevent water damage to the 
Aquatic 2. Keep in mind, the Hartford Loop should also be hanging above water level. 

This means there is no power to the Aquatic 2. Check the electrical connections and then 
the fuse. 

TROUBLESHOOTING

Possible Cause

Corrective Action

The unit and pump did not operate long 
enough

Increase the operating time (minimum 6 hours is 
recommended)

Total alkalinity is not correct

Adjust total alkalinity between 80 and 150 ppm

pH is not correctly balanced

Check for proper pH between 7.2 and 7.6

Not enough suction

Clearanyobstructioninthewaterlinesorreturnfitting,
straighten any kinks in the water or ozone plumbing, 
andcleanthespafilter.

The filter is dirty, loose or cracked

Check/replacethespafilterasneeded.

There are metals or minerals in the water

Ozone may react with metals or minerals in the water 
(this is common when new water is added) causing 
cloudywater.Checkalkalinity,pHandcleanfilter.Run
filtrationsystemandozone24hours.

 


background image

WARRANTY

12

A2Z Ozone Systems Inc. - ONE YEAR LIMITED WARRANTY
The limited warranty set forth below applies to products manufactured by A2Z Ozone Systems Inc. - and sold by 
A2ZOzoneSystemsoritsauthorizeddealers.Thislimitedwarrantyisgivenonlytothefirstretailpurchaserofsuch
products and is not transferable to any subsequent owners or purchasers of such products. A2Z Ozone warrants 
that it or its authorized dealers will repair or replace, at its option, any part of such products proven to be defective 
in materials or workmanship within ONE (1) year from the date of retail purchase of such products. (All parts) 
ANY REPAIR OR REPLACEMENT WILL BE WARRANTED ONLY FOR THE BALANCE OF THE ORIGINAL WARRANTY 
PERIOD. NOTE: USE ONLY A2Z Ozone AUTHORIZED REPLACEMENT PARTS. USE OF ANY OTHER PART(S) WILL 
AUTOMATICALLY VOID THIS WARRANTY. THIS LIMITED WARRANTY DOES NOT INCLUDE ANY OF THE FOLLOWING: 
(a) Any labor charges for troubleshooting, removal, or installation of such parts;
(b) any repair or replacement of such parts necessitated by faulty installation, improper maintenance, improper 
operation,misuse,abuse,negligence,accident,fire,repairmaterial,and/orunauthorizedaccessories;
(c) Any such products installed without regard to required local codes and accepted trade practices; 
(d) ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR PARTICULAR 
PURPOSE, AND SUCH WARRANTIES ARE HEREBY DISCLAIMED: AND 
(e) A2Z Ozone SHALL NOT BE LIABLE UNDER ANY CIRCUMSTANCES FOR LOSS OF USE OF SUCH PRODUCTS, LOST 
PROFITS, DIRECT DAMAGES, INDIRECT DAMAGES, CONSEQUENTIAL DAMAGES AND/OR INCIDENTAL DAMAGES.
TO OBTAIN WARRANTY SERVICE
Contact A2Z Ozone, 1844 Cargo Court Louisville, KY 40299, USA
Customer Service Number: +1 502-499-4977.
Whenfilingaclaim,youmustprovide:
1) Your name, mailing address and telephone number
2) The selling dealer’s name 
3) Proof of date of purchase
4) The date of failure 
5) A description of the failure.
After this information is provided, A2Z Ozone will release a RETURN GOODS AUTHORIZATION (RAN) NUMBER. 
After receiving the RAN number the part in question must be returned to A2Z Ozone, freight prepaid, with the 
RAN number clearly marked on the outside of the package. All preauthorized defective parts must be returned 
to A2Z Ozone within thirty (30) days. Under no circumstances may any product be returned to A2Z Ozone without 
prior authorization. You must call or write prior to returning product or your returned goods shipment will be 
refused. Upon receipt of preauthorized returned goods, A2Z Ozone will repair or replace, at its option, the defective 
product(s) and return them freight (prepaid for products under warranty). Buyer’s acceptance of the product and 
use thereof constitutes acceptance of these terms.

 


background image

A2Z Ozone WARRANTY REGISTRATION CARD

This information can be also send by EMAIL to us. Please provide ALL pertinent information and send 
within twenty (20) days to:      service@a2zozone.com

Otherwise,pleasefilloutcompletelyandreturntoA2ZOzonebypostwithintwenty(20)daysof
purchase.
Customer Info:
Name__________________________________________________________
Address________________________________________________________
City__________________________________State_________Zip__________
Phone (____ ) ________________

Dealer Info:
Dealer Name______________________________
Dealer Address_______________________________________________________
City_________________________________State_________Zip__________
Phone (      ) ________________

Purchase/Product Info:
Purchased Date: _______________________Date Installed____________________
Product Purchased:  SWIMMING POOL A2Z S-SERIES OZONE GENERATOR

Comments / Questions:

DO NOT FORGET TO CUT OUT, PLACE IN ENVELOPE AND MAIL TO THE FOLLOWING ADDRESS FOR 
INSTANT WARRANTY COVERAGE!
A2Z Ozone Systems Inc.
ATTN: Warranty Dept.
1844 Cargo Court
Louisville, KY 40299, USA