PDF User Manual

  1. Home
  2. Manuals
  3. 3Com 3CRWX315075A - Wireless LAN Managed Access Point 3150 Quick Start Manual

3Com 3CRWX315075A - Wireless LAN Managed Access Point 3150 Quick Start Manual

Made by: 3Com
Type: Quick Start Guide
Category: Wireless Access Point
Pages: 17
Size: 0.65 MB

 

Download PDF User Manual


Related Product Video

 

Full Text Searchable PDF User Manual



background image

Quick Start Guide

3Com

®

 WLAN Managed AP3150

3CRWX315075A / Model AP3150

The 3Com® AP3150 Managed Access Point provides dual-radio IEEE 802.11a and 802.11b/g 
wireless access to the network. The access point is designed for use with a 3Com Wireless LAN 
Switch, and requires hardware installation only. All configuration for the access point takes place 
on the 3Com Wireless LAN Switch.

You must have a wireless switch device to operate the access point. The following WLAN switch 
devices can be connected to the access point: 

Power is supplied using Power Over Ethernet (PoE). The following 3Com PoE devices may be used 
to supply power to the access point: 

About This Guide

This Quick Start Guide describes the basic installation of the access point. It covers the following 
topics:

3Com AP3150 Managed Access Point Features

Observing Safety Precautions

Step 1: Unpacking the Access Point

Step 2: Preparing for Installation

Step 3: Attaching the Antennas

Step 4: Mounting the Access Point

Step 5: Connecting the Access Point to a Switch

Step 6: Checking the LED Indicators

Recovery to Managed Mode

Troubleshooting

3Com WX4400

3Com WX2200

3Com WX1200

3Com WXR100

3Com PoE Injector

3Com 4400PWR PoE Switch

3Com Multi-port PoE power supply

3Com WX1200

3Com WXR100

3Com Baseline Switch 2426-PWR Plus

 


background image

2

3Com AP3150 Managed Access Point Features   

Feature

Description

1

Antenna 
Connectors

Two RSMA type antenna connectors allow you to connect antennas 
that operate in 2.4 GHz and 5.0 GHz bands.

2

LEDs

The LEDs indicate power and activity. See “Checking the LED 
Indicators” on page 9 for details.

3

Ethernet Port

The Ethernet port provides a 10/100BASE-TX Ethernet connection to a 
3Com Wireless LAN switch. The connection can be direct to a 3Com 
switch or indirect through an intermediate Layer 2 or Layer 3 network.

Use a standard Category 5 cable with straight-through signaling and 
standard RJ-45 connectors to connect the access point to the switch 
on the network.

4

Serial Port

The serial port is not supported.

5

Reset Button

To restore factory settings, press the reset button during power-up by 
inserting a pointed object into the reset hole on the back of the access 
point and holding for at least 20 seconds. XREF.

6

Kensington lock connector

7

Detachable rear-panel cover

8

Mounting Bracket

The mounting bracket comes attached to the access point and allows 
the unit to be mounted on a wall or ceiling.

2

6

4

3

1

5

7

8

1

 


background image

3

Observing Safety Precautions

This equipment must be installed in compliance with local and national building codes, regulatory 
restrictions, and FCC rules. For the safety of people and equipment, only professional network 
personnel should install the access point. 

You must read the following safety information carefully before you install or remove the unit. 

WARNING:  Warnings contain directions that you must follow for your personal safety. 
Follow all directions carefully.

WARNING:  Exceptional care must be taken during installation and removal of the unit.

WARNING:  The socket outlet must be near to the unit and easily accessible. You can 
only remove power from the unit by disconnecting the power cord from the outlet.

WARNING:  This unit operates under SELV (Safety Extra Low Voltage) conditions 
according to IEC 950 / IEC 60950. The conditions are only maintained if the equipment 
to which it is connected also operates under SELV conditions.

WARNING:  There are no user-replaceable fuses or user-serviceable parts inside the 
unit. If you have a physical problem with the unit that cannot be solved with problem 
solving actions in this guide, contact your supplier.

WARNING:  Disconnect the power adapter before moving the unit.

WARNING:  RJ-45 ports. These are shielded RJ-45 data sockets. They cannot be used 
as standard traditional telephone sockets, or to connect the unit to a traditional PBX or 
public telephone network. Only connect RJ-45 data connectors, network telephony 
systems, or network telephones to these sockets.

Either shielded or unshielded data cables with shielded or unshielded jacks can be 
connected to these data sockets.

WARNING:  To comply with FCC radio frequency (RF) exposure limits, a minimum 
body-to-antenna distance of 20 cm (8 in.) must be maintained when the access point is 
operational.

 


background image

4

Informacje na temat bezpieczeñstwa

Urządzenie musi być zamontowane zgodnie z lokalnymi i krajowymi normami, ustawami 

 

i przepisami. W celu zagwarantowania bezpieczeństwa osób i urządzeń, instalację Punktu 
dostępowęgo może przeprowadzać wyłącznie wyszkolony fachowiec ds. sieci. 

Przed przystąpieniem do montażu lub demontażu urządzenia należy dokładnie przeczytać 
następujące informacje dotyczące bezpieczeństwa.             

OSTRZEŻENIE:  Ostrzeżenia zawierają wskazówki, których należy przestrzegać 

 

w celu zagwarantowania bezpieczeństwa osobistego. Do tych zaleceń należy 
stosować się dokładnie.

OSTRZEŻENIE:  Podczas montażu lub demontażu urządzenia należy pracować 

 

z wyjątkową uwagą.

OSTRZEŻENIE:  Gniazdo sieciowe powinno znajdować się w pobliżu urządzenia 

 

i być łatwo dostępne. Z urządzenia można odciąć zasilanie wyłącznie poprzez 
wyjęcie kabla zasilającego z gniazda.

OSTRZEŻENIE:  Urządzenie działa w warunkach SELV (obwód bezpiecznego 
niskiego napięcia) zgodnie z normą IEC 950 / IEC 60950. Warunki te są jednak 
zagwarantowane wyłącznie wtedy, gdy sprzęt, do którego podłączone jest 
urządzenie, również pracuje w obwodzie SELV.

OSTRZEŻENIE:  Wewnątrz urządzenia nie znajdują się wymienne bezpieczniki lub 
części, które mogłyby być oddane do naprawy. W przypadku wystąpienia problemu, 
którego nie można rozwiązać za pomocą wskazówek podanych w tej instrukcji 
obsługi, prosimy o kontakt z dostawcą produktu.

OSTRZEŻENIE:  Przed przeniesieniem urządzenia należy odłączyć zasilacz.

OSTRZEŻENIE:  Porty RJ-45. Są to ekranowane gniazda RJ-45 do danych. Nie są 
przeznaczone do użycia jako standardowe gniazda telefoniczne lub do podłączenia 
urządzenia do PBX lub publicznej sieci telefonicznej. Do tych gniazd wolno 
podłączać wyłącznie wtyki RJ-45 danych, systemów telefonii sieciowej lub telefonów 
sieciowych.

Do tych gniazd można podłączać kable danych ekranowane lub nieekranowane 

 

z ekranowanymi lub nieekranowanymi wtykami.

OSTRZEŻENIE:  W związku w ograniczeniami częstotliwości radiowej (RF), 
minimalna odległość między ciałem a anteną wynosząca 20 cm (8 cali) musi być 
zachowana w przypadku stosowania Punkt dostępowy.

 


background image

5

1. Unpacking the Access Point

Make sure that you have the following items, which are included with the access point:

Two external 2.4 GHz and 5 GHz dual-band antennas

Mounting bracket (attached to the access point)

Wall-mounting hardware:

Four adhesive rubber feet (used for a flat-surface installation).

2. Preparing for Installation

It is advisable to connect the power (if using an external power supply) and check the Ethernet 
cables and LEDs before installing the access point in a hard-to-reach location. Additionally, 
observe the following items before mounting or connecting the access point: 

Installation Item

Description

Switch port

3Com recommends that you install and configure the 3Com Wireless 
LAN switch before installing the access point. Set the port type on the 
switch to an AP3150 access point.

Cabling

Make sure that standard Category 5 cable with straight-through 
signaling is installed at the site before you install the access point.

Make sure that the cable is highly flexible and that there is no extra 
covering on the RJ-45 connector that could prevent the cable from 
being routed through the mounting bracket.

Power Requirements

Power must be supplied from an 802.3af Power Over Ethernet (PoE)-
compliant device.

If using an external PoE power injector, make sure the power outlet is 
accessible. The power supply plug is the only means of disconnecting 
the access point from power.

MAC Address

Record the access point MAC address in a safe place before the access 
point is installed in a hard-to-reach location.

The MAC address is printed on the back of the access point. Additional 
MAC address labels are shipped with the access point.

 


background image

6

3. Attaching the Antennas

Carefully unpack the standard detachable antennas. Screw the antennas on to the antenna 
connectors on the access point and hand-tighten them. After network startup, you may need to 
adjust the antennas to fine-tune coverage in your area. For best results, adjust the antennas so 
that they are perpendicular with the floor and ceiling. 

Connecting Optional External Antennas

The access point has connectors for attaching optional external antennas and antenna cables. The 
tables below list the external antenna and cable models that are certified for use with the access 
point.   

The 3Com antennas are dual-band, which means that they operate in both 2.4 GHz and 5 GHz 
spectra. You can use these antennas with either the 802.11b/g radio or the 802.11a radio. Each 
antenna requires the purchase of a separate antenna cable. For installation instructions, see the 
documentation that is supplied with the antenna.   

CAUTION:  Do not handle the antenna tips, especially after they are connected to the access 
point. This could lead to electrostatic discharge (ESD), which could damage the equipment.

Antenna Model

Type

3CWE591

3Com 6/8 dBi Dual-Band Omnidirectional Antenna

3CWE592

3Com 3/4 dBi Dual Band Ceiling Antenna

3CWE597

3Com 6/8 dBi Dual-Band Hallway Antenna

3CWE598

3Com 8/10dBi Dual-Band Panel Antenna

Cable Model

Type

3CWE580

3Com Ultra Low Loss 6-Foot Antenna Cable

3CWE581

3Com Ultra Low Loss 20-Foot Antenna Cable

3CWE582

3Com Ultra Low Loss 50-Foot Antenna Cable

3CWE586

3Com RSMA to SMA 6-inch Antenna Cable

 

Note 3CWE586 is required when using any of the external antennas

NOTE: Antenna cables introduce loss of the RF signal. Always use the shortest cable that 
your application allows.

NOTE: During the installation, connect the antenna to the access point before connecting 
the Category 5 Ethernet cable. This ensures that the access point is not powered on when 
the antenna connections are made.

 


background image

7

4. Mounting the Access Point

The access point can be mounted on the following types of surfaces:

Wall, ceiling, or electrical box (NEMA enclosure)

Tabletop

Wall, Ceiling, or Electrical Box Mounting

Use the mounting bracket that comes with your access point to install it on a wall, ceiling, or 
electrical box.

To wall-mount the access point:

1

Route Ethernet cable through the opening in the cradle.

2

Screw the mounting bracket to a wall, ceiling, or electrical box (NEMA enclosure):

If mounting to a solid surface wall or ceiling, use the two sheet metal screws.

If mounting to drywall, use the two sheet metal screws and two wall anchors.

If mounting to an electrical box (NEMA enclosure), use the two threaded screws.

The figures below show a cable being routed through the large opening in the cradle and 
then the cradle being mounted to a wall. 

3

Connect the Ethernet cable (for power and network connection) to the port on the rear of 
the access point.

4

Twist the access point onto the mounting bracket.

Tabletop Mounting

To install the access point on a flat surface such as a table or desktop:

1

Remove the backing from the four rubber feet and attach them on the bottom of the access 
point.

2

Place the access point on the table.

3

Connect the Ethernet cable (for power and network connection) to the port on the rear of 
the access point.

Wall-mounting the cradle

Routing a cable 

 


background image

8

5. Connecting the Access Point to a Switch

The access point can be powered by the following methods:

By Power Over Ethernet (PoE) supplied over the LAN by a 802.3af PoE compliant device such 
as a switch or hub.

By PoE supplied by an optional 3Com PoE injector (not included). 3Com PoE injectors include 
the 3CNJPSE and 3CNJPSE24 midspan supplies.

Power Over Ethernet (PoE) from the LAN

To power the access point using PoE provided by a switch or other 802.3af compliant device, 
simply plug the network cable from the device into the access point’s Ethernet port. 

Power Over Ethernet from a PoE Injector

To power the access point using a 3Com PoE Injector (available separately), do the following:

1

Connect the LAN cable from the switch or hub to the Hub/Switch port on the 3Com PoE 
Injector (available separately).

2

Next connect a LAN cable from the Ethernet port on the access point to the other port on the 
PoE injector.

3

Plug the PoE Injector into a properly grounded electric outlet.

PoE Switch/Hub

Access Point

3CRWX120695A

  

Wireles

s LAN Swit

ch WX1200

3CRWX

120695

A  Wire

less LA

N Switc

h WX12

00

TO ACC

ESS POINT

TO HUB/SWIT

CH

Switch/Hub

(non-PoE)

Access Point

To Access Point

To Switch/Hub

PoE Injector

 


background image

9

6. Checking the LED Indicators

When the access point is connected to power, LEDs indicate activity as follows: 

LED

Color

Indicates

Power Green

Power On

Amber

Flashing indicates a hardware failure, 
or the system is booting.

Off

Power Off

11a

Green

Indicates that 802.11a 5 GHz wireless 
networking is enabled. If the LED is 
flashing, the wireless link is OK and 
data is being transmitted or received.

Off

The radio is off

11b/g

Green

Indicates that 802.11g 2.4 GHz 
wireless networking is enabled. If the 
LED is flashing, the wireless link is OK 
and data is being transmitted or 
received.

Off

The radio is off

LAN

Green

Indicates a 10/100Base-T network is 
detected at the Ethernet port. If the 
LED is flashing, the link is OK and 
data is being transmitted or received.

Off

No link

 


background image

10

Recovery to Managed Mode

If there is a problem with your access point you may need to reset it to Managed mode.

1

Before you begin, download the latest software AP3150 software image from 
www.3Com.com.

2

Shut down the access point by disconnecting power.

3

Press and hold the Reset button. Reconnect power and continue to hold the Reset button for 
20 seconds. Your access point will restart in Recovery mode.

4

Connect to access point using the a web browser and the default IP address of 
169.254.2.251. When you connect to the unit, the Access Point Recovery Page is 
displayed: 

5

Click the Browse button and navigate to the access point software image file.

6

Click Start Upgrade to update your access point.

7

When the update is complete, click Change Mode to switch the access point to Managed 
mode.

8

Click the Reset button on the Recovery Page to reboot your access point.

Troubleshooting

Refer to the Mobility System Configuration Guide or to the 3Com Wireless LAN Switch Reference 
Manual
 to obtain the access point status.

 


background image

11

R

EGULATORY

 I

NFORMATION

The 3Com WLAN Managed AP3150, Model AP3150 (3CRWX315075A) must be installed and used in strict 
accordance with the manufacturer’s instructions as described in the user documentation that comes with the 
product.

This product contains encryption. It is unlawful to export out of the U.S. without obtaining a U.S. Export 
License.

 

This product does not contain any user serviceable components. Any unauthorized product changes or 
modifications will invalidate 3Com’s warranty and all applicable regulatory certifications and approvals.

This product must be installed by a professional technician/installer.

Only antennas specified for your region by 3Com can be used with this product. The use of external amplifiers or 
non-3Com antennas may invalidate regulatory certifications and approvals.

This product can be used with the following antennas and accessories: 

Suitable RF power levels for internal and external antennas are handled automatically by your 3Com Wireless 
Switch or Controller. Ensure that the switch or controller configuration is modified to use the antenna that is 
connected to the Access Point. Refer to the Mobility System Configuration Guide or to the 3Com Wireless LAN 
Switch Reference Manual
 to modify the access point settings.

CAUTION: E

XPOSURE

 

TO

 R

ADIO

 F

REQUENCY

 R

ADIATION

This device generates and radiates radio-frequency energy. In order to comply with FCC radio-frequency 
exposure guidelines for an uncontrolled environment, this equipment must be installed and operated while 
maintaining a minimum body to antenna distance of 20 cm (approximately 8 in.).

The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not 
emit RF field in excess of Health Canada limits for the general population; consult Safety Code 6, obtainable 
from Health Canada’s website www.hc-sc.gc.ca/rpb.

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. End users 
must follow the specific operating instructions for satisfying RF exposure compliance. This equipment should be 
installed and operated with minimum distance 20 cm between the radiator and your body.

This product must maintain a minimum body to antenna distance of 20 cm. Under these conditions this product 
will meet the Basic Restriction limits of 1999/519/EC [Council Recommendation of 12 July 1999 on the limitation 
of exposure of the general public to electromagnetic fields (0 Hz to 300 GHz)].

Item

Description

Restrictions

Supplied antenna

3CWE591

3Com 6/8dBi Dual-Band Omni Antenna

Must be used with 3CWE586 and one of 
the following: 3CWE580, 3CWE581 or 
3CWE582.

3CWE592

3Com 3/4dBi Dual-Band Ceiling Mount 
Antenna

Must be used with 3CWE586 and one of 
the following: 3CWE580, 3CWE581 or 
3CWE582.

3CWE597

3Com 4/6dBi Dual-Band Hallway Antenna

Must be used with 3CWE586 and one of 
the following: 3CWE580, 3CWE581 or 
3CWE582.

3CWE598

3Com 8/10dBi Dual-Band Panel Antenna

Must be used with 3CWE586 and one of 
the following: 3CWE580, 3CWE581 or 
3CWE582.

3CWE580

3Com Ultra Low Loss 6-Foot Antenna Cable

Must also use 3CWE586. Cannot be used 
with supplied antenna.

3CWE581

3Com Ultra Low Loss 20-Foot Antenna Cable   Must also use 3CWE586. Cannot be used 

with supplied antenna.

3CWE582

3Com Ultra Low Loss 50-Foot Antenna Cable

Must also use 3CWE586. Cannot be used 
with supplied antenna.

3CWE586

3Com RSMA to SMA 6-inch Antenna Cable

Required for all external antennas, except 
that supplied with the Access Point.

i

 


background image

12

US — R

ADIO

 F

REQUENCY

 R

EQUIREMENTS

This device must not be co-located or operated in conjunction with any other antenna or transmitter.

This device is for indoor use only when using channels 36, 40, 44 or 48 in the 5.15 to 5.25 GHz frequency range.

High power radars are allocated as primary users of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These 
radar stations can cause interference with and/or damage this device.

FCC N

OTICE

To comply with FCC Part 15 rules in the United States, the system must be professionally installed to ensure 
compliance with the Part 15 certification. It is the responsibility of the operator and professional installer to 
ensure that only certified systems are deployed in the United States. The use of the system in any other 
combination (such as co-located antennas transmitting the same information) is expressly forbidden in 
accordance with FCC rules CFR47 Part 15.204.

USA—F

EDERAL

 C

OMMUNICATIONS

 C

OMMISSION

 (FCC) EMC C

OMPLIANCE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in 
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not 
installed and used in accordance with the instructions, may cause harmful interference to radio communications. 
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does 
cause harmful interference to radio or television reception, which can be determined by turning the equipment 
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

The user may find the following booklet prepared by the Federal Communications Commission helpful: The 
Interference Handbook
. This booklet is available from the U.S. Government Printing Office, Washington, DC 
20402. Stock No. 004-000-0034504.

3Com is not responsible for any radio or television interference caused by unauthorized modification of the 
devices included with this 3Com WLAN Managed AP, Model AP3150 (3CRWX315075A), or the substitution or 
attachment of connecting cables and equipment other than specified by 3Com.

The correction of interference caused by such unauthorized modification, substitution or attachment will be the 
responsibility of the user.

Changes or modifications not expressly approved by 3Com could void the user's authority to operate this 
equipment.

US M

ANUFACTURER

S

 FCC D

ECLARATION

 

OF

 C

ONFORMITY

3Com Corporation

 

350 Campus Drive

 

Marlborough, MA 01752-3064, USA

 

(508) 323-5000

Date: 1 March 2007

Declares that the Product:

 

Brand Name: 3Com Corporation

 

Model Number: AP3150

 

Equipment Type: WLAN Managed AP3150

Complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not 
cause harmful interference, and (2) this device must accept any interference received, including interference that may 
cause undesired operation. 

3Com WLAN Managed AP3150

 

Model AP3150

 


background image

13

I

NDUSTRY

 C

ANADA

 — RF C

OMPLIANCE

This device complies with RSS 210 of Industry Canada.

Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this 
device must accept any interference, including interference that may cause undesired operation of this device.

L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes: (1) il ne doit pas produire de 
brouillage et (2) l’utilisateur du dispositif doit étre prêt à accepter tout brouillage radioélectrique reçu, même si 
ce brouillage est susceptible de compromettre le fonctionnement du dispositif.

The term “IC” before the equipment certification number only signifies that the Industry Canada technical 
specifications were met.

To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the 
equivalent isotropically radiated power (EIRP) is not more than that required for successful communication. To 
prevent radio interference to the licensed service, this device is intended to be operated indoors and away from 
windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject 
to licensing.

Pour empecher que cet appareil cause du brouillage au service faisant l'objet d'une licence, il doit etre utilize a 
l'interieur et devrait etre place loin des fenetres afin de Fournier un ecram de blindage maximal. Si le matriel (ou 
son antenne d'emission) est installe a l'exterieur, il doit faire l'objet d'une licence.

High power radars are allocated as primary users of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These 
radar stations can cause interference with and/or damage this device.

This device must not be co-located or operated in conjunction with any other antenna or transmitter.

The band 5150-5250 MHz is only for indoor usage to reduce the potential for harmful interference to co-
channel mobile satellite systems.

This device has been designed to operate with the antennas listed at the start of the Regulatory Information 
section above (page 11), and having a maximum gain of 8 dB (2.4 GHz) or 10 dB (5 GHz). Antennas not 
included in this list or having a gain greater than 8 dB (2.4 GHz) or 10 dB (5 GHz) are strictly prohibited for use 
with this device. The required antenna impedance is 50 ohms.

I

NDUSTRY

 C

ANADA

 - E

MISSIONS

 C

OMPLIANCE

 S

TATEMENT

This Class B digital apparatus complies with Canadian ICES-003.

Avis de Conformité à la Réglementation d'Industrie Canada

Cet appareil numérique de la classe B est conform à la norme NMB-003 du Canada.

S

AFETY

 C

OMPLIANCE

 N

OTICE

This device has been tested and certified according to the following safety standards and is intended for use only 
in Information Technology Equipment which has been tested to these or other equivalent standards:
• UL Standard 60950-1
• CAN/CSA C22.2 No. 60950-1
• IEC 60950-1
• EN 60950-1

EU C

OMPLIANCE

    

Intended use: IEEE 802.11a/b/g radio LAN device

AT

BE

CY

CZ

DK

EE

FI

FR

DE

GR

HU

IE

IT

LV

LT

LU

MT

NL

PL

PT

SK

SI

ES

SE

GB

IS

LI

NO

CH

BG

RO

TR

This equipment may be operated in

 


background image

14

NOTE: To ensure product operation is in compliance with local regulations, select the country in which the 
product is installed. 

Česky [Czech]

3Com Coporation tímto prohlašuje, že tento RLAN device je ve shodě se základ-
ními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.

Dansk [Danish]

Undertegnede 3Com Corporation erklærer herved, at følgende udstyr RLAN 
device overholder de væsentlige krav og øvrige relevante krav i direktiv 
1999/5/EF.

Deutsch [German]

Hiermit erklärt 3Com Corporation, dass sich das Gerät RLAN device in Überein-
stimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen 
Bestimmungen der Richtlinie 1999/5/EG befindet.

Eesti [Estonian]

Käesolevaga kinnitab 3Com Corporation seadme RLAN device vastavust direkti-
ivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjako-
hastele sätetele.

English

Hereby, 3Com Corporation, declares that this RLAN device is in compliance with 
the essential requirements and other relevant provisions of Directive 1999/5/EC.

Español [Spanish]

Por medio de la presente 3Com Corporation declara que el RLAN device cum-
ple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o 
exigibles de la Directiva 1999/5/CE.

Ελληνική [Greek]

ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ 3Com Corporation ΔΗΛΩΝΕΙ ΟΤΙ RLAN device 
ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ 
ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.

Français [French]

Par la présente 3Com Corporation déclare que l'appareil RLAN device est con-
forme aux exigences essentielles et aux autres dispositions pertinentes de la 
directive 1999/5/CE.

Italiano [Italian]

Con la presente 3Com Corporation dichiara che questo RLAN device è con-
forme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla 
direttiva 1999/5/CE.

Latviski [Latvian]

Ar šo 3Com Corporation deklarē, ka RLAN device atbilst Direktīvas 1999/5/EK 
būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.

Lietuvių [Lithuanian]

Šiuo 3Com Corporation deklaruoja, kad šis RLAN device atitinka esminius reika-
lavimus ir kitas 1999/5/EB Direktyvos nuostatas.

Nederlands [Dutch]

Hierbij verklaart 3Com Corporation dat het toestel RLAN device in overeenstem-
ming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 
1999/5/EG.

Malti [Maltese]

Hawnhekk, 3Com Corporation, jiddikjara li dan RLAN device jikkonforma mal-
htigijiet essenzjali u ma provvedimenti ohrajn relevanti li hemm fid-Dirrettiva 
1999/5/EC.

Magyar [Hungarian]

Alulírott, 3Com Corporation nyilatkozom, hogy a RLAN device megfelel a vonat-
kozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.

Polski [Polish]

Niniejszym 3Com Corporation oświadcza, że RLAN device jest zgodny z zasad-
niczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 
1999/5/EC.

Português 

 

[Portuguese]

3Com Corporation declara que este RLAN device está conforme com os requisi-
tos essenciais e outras disposições da Directiva 1999/5/CE.

Slovensko [Slovenian]

3Com Corporation izjavlja, da je ta RLAN device v skladu z bistvenimi zahtevami 
in ostalimi relevantnimi določili direktive 1999/5/ES.

Slovensky [Slovak]

3Com Corporation týmto vyhlasuje, že RLAN device spĺňa základné požiadavky 
a všetky príslušné ustanovenia Smernice 1999/5/ES.

Suomi [Finnish]

3Com Corporation vakuuttaa täten että RLAN device tyyppinen laite on direkti-
ivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden 
ehtojen mukainen.

Svenska [Swedish]

Härmed intygar 3Com Corporation att denna RLAN device står I överensstäm-
melse med de väsentliga egenskapskrav och övriga relevanta bestämmelser 
som framgår av direktiv 1999/5/EG.

 


background image

15

A copy of the signed Declaration of Conformity can be downloaded from the Product Support web page for the 
3Com WLAN Managed AP3150, Model AP3150 (3CRWX315075A) at http://www.3com.com. Also available at 
http://support.3com.com/doc/AP3150_EU_DOC.pdf

EU - R

ESTRICTIONS

 

FOR

 U

SE

 

IN

 

THE

 2.4 GH

Z

 

BAND

This device may be operated indoors or outdoors in all countries of the European Community using the 2.4 GHz 
band: Channels 1–13, except where noted below. 

• In Italy the end-user must apply for a license from the national spectrum authority to operate this device 

outdoors. 

• In Belgium outdoor operation is only permitted using the 2.46 – 2.4835 GHz band: Channel 13.

• In France outdoor operation is only permitted using the 2.4 – 2.454 GHz band: Channels 1 – 7.

EU - R

ESTRICTIONS

 

FOR

 U

SE

 

IN

 

THE

 5 GH

Z

 

BAND

 

• This device may be not be operated outdoors when using the bands 5150–5350 MHz (Channels 36, 40, 44, 

48, 52, 56, 50, 64).

• In Italy the end-user must apply for a license from the national spectrum authority to operate this device 

outdoors. 

• To remain in conformance with European spectrum usage laws for Wireless LAN operation, the above 5 GHz 

channel limitations apply. The user should check the current channel of operation. If operation is occurring 
outside of the allowable frequencies as listed above, the user must cease operating the Access Point at that 
location and correct the configuration of the channels used before resuming operation.

• The 5 GHz Turbo mode feature is not allowed for operation in any European Community country.

• This device must be used with the radar detection feature required for European Community operation in the 

5 GHz bands. This device will avoid operating on a channel occupied by any radar system in the area. The 
presence of nearby radar operation may result in temporary interruption in communications of this device. 
The Access Point's radar detection feature will automatically restart operation on a channel free of radar. You 
may consult with the local technical support staff responsible for the wireless network to ensure the Access 
Point device(s) are properly configured for European Community operation.

B

RAZIL

 RF C

OMPLIANCE

Este produto está homologado pela ANATEL, de acordo com os procedimentos regulamentados pela  Resolução 
242/2000, e atende aos requisitos técnicos aplicados.

Opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de 
estações do mesmo tipo, e não pode causar interferência a sistemas operando em caráter primário.

Para maiores informações, consulte o site da ANATEL - www.anatel.gov.br

Íslenska [Icelandic]

Hér með lýsir 3Com Corporation yfir því að RLAN device er í samræmi við 
grunnkröfur og aðrar kröfur, sem gerðar eru í tilskipun 1999/5/EC.

Norsk [Norwegian]

3Com Corporation erklærer herved at utstyret RLAN device er i samsvar med de 
grunnleggende krav og øvrige relevante krav i direktiv 1999/5/EF.

Allowed Frequency Bands

Allowed Channel Numbers

Countries

5.15–5.35 & 5.470–5.725 GHz

36, 40, 44, 48, 52, 56, 60, 64, 100, 
104, 108, 112, 116, 120, 124, 128, 
132, 136, 140

Austria, Belgium, Bulgaria, Cyprus, 
Czech Republic, Denmark, Estonia, 
Finland, France, Germany, Greece, 
Hungary, Iceland, Ireland, Italy, 
Latvia, Liechtenstein, Lithuania, 
Luxembourg, Malta, Netherlands, 
Norway, Poland, Portugal, Romania, 
Slovakia, Slovenia, Spain, Sweden, 
Switzerland, U.K.

 


background image

K

OREA

 RF C

OMPLIANCE

This device may cause radio interference during its operation. Therefore service in relation to human life security 
is not available.

T

AIWAN

 RF C

OMPLIANCE

經型式認證合格之低功率射頻電機 , 非經許可 , 公司、商號或使用者均不得擅自變更頻率、加大功率或變更
原設計之特性及功能。低功率射頻電機之使用不得影響飛航安全及干擾合法通信 ; 經發現有干擾現象時 , 應
立即停用 , 並改善至無干擾時方得繼續使用。前項合法通信 , 指依電信法規定作業之無線電通信。低功率射
頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。

C

HINA

 R

O

HS 

 

Copyright © 2007 3Com Corporation. All rights reserved.  3Com and the 3Com logo are registered 
trademarks of 3Com Corporation. All other company and product names may be trademarks of the 
respective companies with which they are associated.

Part Number: 10015915 Rev. AA

 

Published June 2007