Related Product Video
Full Text Searchable PDF User Manual
Connection of OfficeRoute
OfficeRoute has default IP address 10.0.0.1 and mask 255.0.0.0. You can
reach OfficeRoute’s web interface in case that you assign IP address of your
PC from the same range as IP of OfficeRoute.
In case you want to change IP address of OfficeRoute as a first step, you can
use supplied USB cable (it is necessary to install USB driver). Run
Hyperterminal (or another terminal program enabling serial communication),
select COM port assigned to installed USB driver, Set communication speed
921600 bps, flow control:none. When you press Enter, following screen
2N OfficeRoute V1.01 Main Menu 2N OfficeRoute
Option Value Description
1 – Configuration [ menu ] – General configuration
2 – Set Admin password – Set administration password
3 – Help – Display help for serial
Enter an option number, <ESC> previous menu
Select: 1-Configuration, 1-Network settings, you can set IP address, mask
and other network settings.
WARNING: Assigned IP address must not be the same as already existing IP
address in your network.
Type IP address of OfficeRoute into your web browser and you’ll get login
Default login name is Admin , no password.
Settings for UMTS router functionality
SIM card settings
Before you insert SIM card into the unit, it is needed to set PIN code (or
disable PIN code in your mobile phone). After login go to the section
Administration – Main configuration, set PIN code of SIM card here.
If PIN code is stored, power-off the unit, mount antenna and insert SIM
card(s). Then power unit on. When LED indicators are off, it means that SIMs
are logged into to a network. In case that LED indicator shines orange, there’s
no signal of preferred network or PIN is wrong.
Log into the web interface again. You can see SIM cards details in the section
Telephony services – Devices – SIM cards.
Select data SIM card by clicking to the icon with a penci:
Fill GPRS provider name (user defined) and APN (you can find this
information on a web page of network provider or ask his help line).
Sometimes username and password is needed. Don’t fill GPRS number and
GPRS initial AT commands (these settings are not needed for most cases).
Connection to Internet
Save SIM card settings. Switch on connection to Internet in the section
Network – GPRS ON/OFF by clicking to icon with green handset „GPRS“.
After cca 30 seconds LED indicator starts blinking by green colour – it usually
means that it is connected to the network of operator. From this moment it is
connected even you restart the unit or power it off and on again.
For using OfficeRoute as a router for internet connectivity you have to set IP
address of OfficeRoute as Default gateway in you PC and IP addresses of
DNS servers (displayed in the GPRS window).
IP settings can be found in your PC in the section Start – Control panels –
Network connections – Local network settings.
OfficeRoute as DHCP server
OfficeRoute may work also as DHCP server. You can set necessary settings
in Network – DHCP server.
In case that IP of OfficeRoute is 10.0.0.1, then you can use settings from the
Then IP addresses 10.0.0.2-10.0.0.100 are assigned to devices in your LAN.
Also it is necessary to switch on DNS proxy in the menu Network – DNS
proxy – tick Enable DNS proxy.
Settings for SIP IP PBX functionality – how to add a
new account and call to GSM/UMTS
User management>Users>Add user: Adding of a new
User name: SIP authentication name for SIP extension.
New password: SIP authentication password.
Rights/Rights denied: Select rights or left empty – rights
are assigned by group selection except SMS rights.
Line number: Line number is UID (number of
Mobility extension: Number of mobile phone which
receives dual ringing with SIP extension. It is possible to
transfer call from mobile phone. In case you need to set
Outgoing/Incoming ME checkbox and fill his mobile
Voicemail: 2N OfficeRoute is equipped by internal
voicemail. Each user can have own voicemail box
(licensed). Set PIN for entering user’s voicemail and set
his mobile phone number for receiving notification
Internal SIP line
Internal SIP line connects SIP proxy to LCR. You can
imagine it as such gateway to LCR – see picture bellow.
User ‚vbegw‘ is predefined as default user for internal
SIP line with password ‘1234’. Modify internal SIP line
(Telephony services>Devices>SIP lines) following way:
Where ‚SIP server address‘ is IP adres sof OfficeRoute.
Telephony services>LCR>Routes – List of existing
routes and adding and removing routes. A Route means
outgoing trunk (bundle of SIMs, modules, SIP lines or
Fig. 1 – ‘Add route’ form
There is a route named ‘Mobile Networks’ on the picture
which contains all modules, it is being used during all
defined time intervals without suppressing CLI (CLI can
be suppressed for mobile networks only).
LCR rule – Routing of call is based on the called
number. LCR rule basically defines to which Route
dialed numbers are routed (according prefix).
There is an example of a LCR rule. Destination name is
user defined, the rule is applied to called numbers with
prefixes 6 or 7, call is routed to the route ‘ Mobile
networks’ with unknown priority. Priority can be
according free minutes, first free or cycle (for free
minutes and cycle a tariff must be defined for each line
of the route).
LCR test – you can test routing rules after setting all
routing rules and routes. For routing test SIM cards
must be placed in the unit in order to have test fully